Development milestones
First flight: 2 November 1992 ( 1992-11-02 )
Developed from: Airbus A300
機型庫Airbus A330 family
4300streetcar · CC BY 4.0 · Delta Air Lines A330-300Airbus A330 family
A long-haul twin whose family spans passenger, freight and specialist transport roles.
Airliner設定檔選項：19 個
瞭解飛機
Airbus developed the A330 alongside the four-engine A340. The two programmes shared substantial airframe and cockpit work, but the A330 used two engines. The initial A330-300 entered service in 1994; the shorter A330-200 followed in 1998.
The family includes several engine choices, different fuselage lengths and later A330neo developments. These distinctions reach inside the cockpit: engine indications and fuel arrangements are not identical across every version. The simulator products cover different variants, each with its own developer documentation.
Taking a twin-engine airliner to the Antarctic ice
Mirpuri's log describes the preparation behind Hi Fly's A330 mission from Cape Town to Wolf's Fang. The aircraft carried fuel for the return as well as the outward journey, and the team monitored fuel temperature, destination weather and runway condition throughout the flight. Forecast discussions began days beforehand. Ground power and starting equipment at the remote strip were also part of making the twin-engine operation possible.
Four pilots shared the long duty, supported by engineers, cabin crew, a ground coordinator and colleagues at both bases. Mirpuri recalls touching down just before midnight local time, when the Antarctic summer sun was still above the horizon and katabatic winds were beginning to rise. The aircraft stopped as planned, turned and taxied to parking before returning to Cape Town later. His airline-published account stresses the contribution of the whole team to a landing intended to feel uneventful.
A familiar flight deck and a sharper response on approach
Gerzanics flew the A330-800 test aircraft F-WTTO from Toulouse with Airbus test pilot Thomas Wilhelm. Although he did not routinely fly Airbus aircraft, the common cockpit felt familiar. The aircraft was still contributing to flight-control development, and a special display helped him practise the consistent sidestick input needed for the takeoff test. In the air, he found it easy to establish bank angles and roll out accurately on a heading.
On the return, the instrument landing system's glideslope went out of service. Wilhelm suggested using the head-up display while setting up an alternative ground-augmented satellite approach. Gerzanics then assessed the aircraft's response by deliberately offsetting from, and rejoining, the final approach course. He found the response crisp and the landing straightforward. This was an organised evaluation in an instrumented A330-800, including test manoeuvres.
Learning to wait for a larger aircraft’s response
After thirteen years flying the A320 family around Europe, Harder was preparing to return to long-haul work on the A330. He describes receiving the training assignment after applying for a conversion, then working through technical material at home before moving into procedural and full-flight simulators. His Airbus experience shortened part of the training, but the new aircraft still had different systems to learn.
Asked how the A330 felt in the simulator, he noticed a more delayed response to control inputs, reminding him of his earlier experience as a Boeing 747 first officer. He had to allow a little time for the larger aircraft to respond. At the time of the interview, his simulator check and line training still lay ahead. His conversion training took place in the simulator; he had not yet completed his A330 qualification.
公開來源 21
- Airbus A330Research background · Wikipedia revision 1373820047 · retrieved 2026-09-12
- Airbus A330
- Microsoft Flight Simulator aircraft manuals
- MSFS 2024 FAQ and edition aircraft inventory
- Airbus Beluga XL
- Airbus A330-300 POH
- X-Plane 12 Desktop Manual
- X-Plane aircraft and avionics manuals
- A330-900 change log
- A330 900Official developer / designated store catalogue · checked 2026-09-12
- Captain’s log: landing the first Airbus A330 in AntarcticaCarlos Mirpuri · 5 December 2025
- The flight test of Airbus’s refreshed widebody – the A330neoMike Gerzanics · 2019
- Umschulung auf den Airbus A330 – Upgrade für einen KapitänClaus Harder · 5 May 2023
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- Aerosoft Aircraft A330 neoProduct listing captured 28 September 2026; A330-900neo, MSFS 2024
- A330-300Product listing captured 2026-09-24; edition scope from the reviewed catalogue
- A339X A330-900neoProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- JARDesign 330 Airliner -JARDesign-A330Product listing captured 2026-09-30; edition scope from the reviewed catalogue
- Airbus A330-200 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Airbus A330-300 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Airbus A330-900neo exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
設定檔如何建模
AeroGenesis A330-300 (RR / PW / GE)
Free + ProX-Plane 12AeroGenesis
Airbus developed the A330 alongside the four-engine A340. The two programmes shared substantial airframe and cockpit work, but the A330 used two engines. The initial A330-300 entered service in 1994; the shorter A330-200 followed in 1998.
This profile selects AeroGenesis A330-300 (RR / PW / GE) for X-Plane 12.
The spring stays independent of airspeed. Directed aerodynamic loading is omitted.
Pitch-trim relief is off. Autopilot following is off.
此確切修訂版尚未開放公開安裝。
Controls and trim
The A330 cockpit uses Airbus sidesticks and fly-by-wire. The bundled manual separates the -200/-300 fuel and trim-tank arrangements, while the Beluga XL has its own flight-control and autopilot guide. A330neo, passenger-to-freighter and corporate configurations retain their model identities. Aircraft trim and autopilot guidance belong to the flight-control system; they do not establish surface-airload feedback through a passive stick.
The selected implementation
AeroGenesis reworks Laminar's XP12 A330, with RR/PW/GE runtime engine choices. Later XP12.4 changes supersede some custom features; its older README version is not the current release label.
About the values
The gains are normalized profile settings. They describe the chosen effect balance; hand force depends on the device and its output limits. IAS references are tuning values rather than operating limits. Physical acceptance of this revision remains pending.
Master gain & control system
Master gain85%
施加於模型產出的一切、在裝置上限之前的最終整體輸出縮放。
調高: 一切(彈簧、載荷、效果)一同增強。
調低: 一切一同變柔。
設定理由: Scales overall profile strength while preserving effect balance, subject to device and output limits.
Forces
Spring strength55%
把搖桿拉回中央的基礎回中力。其他所有力都疊加在它之上。太低,正常飛行中搖桿會發軟;太高,它會與你的手較勁,並掩蓋疊加其上的細微提示。
調高: 更硬的回中,更抗手。
調低: 更軟的桿,只靠氣動載荷。
設定理由: Fixed sidestick centering represents the Airbus control arrangement while keeping aircraft control-law behavior separate from hardware resistance. The baseline spring is 0.55. Low-speed spring blending is off.
Cockpit and flight control familiesAirbus A330Airbus Beluga XLSpring deadband1%
中央附近彈簧保持安靜的小中立區,讓靜止時的微小移動不會咔嗒作響。更寬更安穩但更松,更窄更精確但可能在中央附近抖動。
調高: 更安靜但更松的中央,曠量更大。
調低: 更緊的中央,靜止時可能抖動。
設定理由: Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner.
Forces · Center starting force0.03
設定理由: The centre preload is 0.03. It ramps outside the 0.01 deadband across 0.05 travel, shaping the passive centre independently of aircraft autotrim.
Forces · Center starting force transition0.05
設定理由: Sets the travel used to ramp in centre preload. Wider intervals make its onset more gradual.
Overall aerodynamic load24%
作用於兩條持續軸載荷的主縮放,在它們各自的獨立平衡之前施加。設定檔通常不動它,而是調校兩條軸載荷。
調高: 兩軸載荷一同加重。
調低: 兩軸一同減輕。
設定理由: The stored 0.24 aerodynamic-load gain is inactive under the fixed-centre control law.
Airspeed blendingFalse
啟用低速彈簧介入視窗(上面的起始/全強度節數)。關閉時彈簧在所有速度下恆定。
設定理由: Allows baseline spring strength to rise with indicated airspeed where the control law permits it.
Low-speed spring floor55%
在靜止、空速尚未產生氣動力之前,彈簧還剩多少。下限高,停機時搖桿結實;下限低,則是停放輕型飛機那種鋼索鬆弛的感覺。
調高: 停機和滑行時桿更結實。
調低: 停機時桿發軟,只隨速度甦醒。
設定理由: Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength.
Spring engagement start20 kt
彈簧從低速下限開始向全強度攀升的空速:起飛滑跑中操縱面"甦醒"的那一刻。
設定理由: Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit.
Spring engagement full70 kt
彈簧達到全強度的空速。從起點到這裡,隨著氣流在操縱面上增強,回中逐漸變硬。
設定理由: Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
力回饋調校速度250
氣動載荷達到設計滿值的指示空速。它把整條載荷曲線錨定在飛機真實的速度範圍:172在110節就載滿,噴氣機要晚得多。
調高: 載荷來得更晚;桿輕到更高速度。
調低: 載荷來得更早,巡航更沉。
設定理由: Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Centre firmness vs speed0%
在偏轉載荷之外,回中本身隨速度變硬的程度。零則中央手感恆定;越大,巡航時回中越硬,起落航線上越松。
調高: 中央隨速度明顯變硬。
調低: 任何速度下中央手感恆定。
設定理由: Adds permitted spring resistance above the full-blend speed. Zero removes this high-speed increase.
Centre stiffening cap2
速度驅動的中央變硬上限,防止高速飛行把彈簧無限上緊。
調高: 高速允許更多總硬化。
調低: 硬化更早封頂。
設定理由: Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap.
Aileron load65%
由副翼偏轉和空速產生的持續橫滾載荷,獨立於俯仰調校。與升降舵載荷一起,決定評測中常說的操縱協調比。
調高: 橫滾力更重。
調低: 副翼更輕更靈。
設定理由: Roll and pitch aerodynamic scales are 0.65 and 0.86, respectively. These stored weights do not create directed aerodynamic loading while that term is inactive. The pitch spring-travel curve reaches output 1 at input 1. The roll spring-travel curve reaches output 0.3 at input 1. Spring-travel response contributes separately to axis balance.
Elevator load86%
由升降舵偏轉和空速產生的持續俯仰載荷,獨立於橫滾調校。這是決定機型俯仰重量的主槓桿。它不影響副翼、彈簧、配平或抖振力。
調高: 速度下持續俯仰力更重。
調低: 升降舵更輕,握持更省力。
設定理由: Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Max output force55%
每個穩態俯仰或橫滾力到達裝置前的上限,防止猛烈機動中砸擊或飽和硬體。
調高: 削波前更高的穩態力峰值。
調低: 更柔的上限;猛烈機動更早被抹平。
設定理由: Caps directed-force output. Native spring effects and device limits remain separate.
Trim
Trim relief (elevator)0%
升降舵配平緩解持續俯仰力、移動桿的安定位置的強度。在100 %時,配平得當的飛機不需要保持壓力——正是真實飛行中"用配平消掉載荷"的流程。
調高: 配平消掉更多持續力;100 %時滿配平可完全抵消。
調低: 即使配平也仍要持續用力。
設定理由: Aircraft automatic trim is independent of the selected passive stick centre; the trim-tank arrangement is not a hardware trim command. Pitch relief is off, with stored authority 0; roll authority is 0.
Cockpit and flight control familiesAirbus A330Airbus Beluga XLTrim relief (aileron)0%
橫滾配平的同類緩解。多數通航機型沒有真正的副翼配平,所以保持為零;有橫滾配平的機型獲得相應的值。
調高: 橫滾配平消掉更多持續力。
調低: 橫滾配平作用更小。
設定理由: Scales supported roll-trim relief and permitted centre movement. Zero removes roll response.
Effect gains · Ground
Runway rumble0%
由輪速和地面型別(鋪裝、草地、礫石)產生的滾動振動。
調高: 桿上更強的地面質感。
調低: 更平滑的滑行。
設定理由: Sets rolling texture strength, modified by speed, surface and undercarriage configuration.
Gear bumps0%
來自伸縮縫、車轍和粗糙地面的短促離散顛簸,為持續隆隆聲打上標點。
調高: 接縫與車轍的衝擊更清晰。
調低: 更柔的地面細節。
設定理由: Sets gear-bump texture during ground motion, separate from touchdown impact.
Effect gains · Airframe
Stall buffet6%
接近失速及失速警告響起時的機體抖動:這副機翼宣告不滿的音量。斷失乾脆的機型抖振收斂,讓喇叭承擔警告。
調高: 更強的失速前顫抖。
調低: 更含蓄的機翼;警告交給喇叭。
設定理由: Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings.
Mach buffet6%
接近馬赫極限的跨音速抖振。對接近MMO的噴氣機有意義,對到不了那裡的活塞機和渦槳機為零。
調高: 接近馬赫極限時更強的跨音速抖振。
調低: 高馬赫下更平滑的飛行。
設定理由: Sets high-Mach buffet strength; onset and full-strength thresholds are separate.
Flap buffet0%
襟翼伸入氣流後機體的低頻振動,發生在它們真正做功的速度視窗內。
調高: 襟翼做功時更粗糙的飛行。
調低: 更柔的進近襟翼。
設定理由: Sets flap buffet at the configured position and speed gates. Flap movement texture is separate.
Gear buffet0%
可收放起落架懸在氣流中引起的機體鼓振。固定起落架機型為零,它們的機體外形從不改變。
調高: 放起落架時更多鼓振。
調低: 放起落架飛行更乾淨。
設定理由: Sets gear aerodynamic buffet; movement and ground-contact cues are separate.
Stick shaker50%
由飛機自身失速警告系統觸發的專用抖桿器振動。只有真有抖桿器的機型才有值;其餘全靠氣動抖振和喇叭。
調高: 更硬的抖桿器。
調低: 更含蓄的抖桿器。
設定理由: Sets triggered shaker strength; inactive while the shaker feature is disabled.
Effect gains · Engine, mechanical & drag
Touchdown thump0%
機輪觸及跑道那一下的單次衝擊,按下沉率縮放:輕柔著陸是耳語,結實到達是一記悶響。
調高: 觸地時更硬的一擊。
調低: 更柔的到達。
設定理由: Sets landing-impact strength; landing telemetry and response shape determine the pulse.
Reverse rumble0%
反推或槳葉beta區工作時的滑跑振動。無反推機型為零。
調高: 反推下更粗糙的滑跑。
調低: 更含蓄的反推。
設定理由: Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue.
Engine rumble0%
從慢車到全功率跟隨轉速的持續動力裝置振動——前方有東西在燒油的永恆提醒。
調高: 桿裡更多引擎。
調低: 更含蓄的引擎。
設定理由: Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration.
Flap motion0%
僅在模擬器報告襟翼舵面確實移動時的持續振動。它跟隨真實作動器的運動和故障,而非估算的計時器。
調高: 襟翼移動中更多振動。
調低: 更含蓄的襟翼行程。
設定理由: Sets texture from observed flap movement; a command without movement does not establish the cue.
Autopilot follow
AP follow authority5%
自動駕駛指令可以讓桿實際移動多遠。在MSFS中保持極小,因為移動的軸可能被讀回為飛行員輸入;零則完全停用跟隨。
調高: 自動駕駛讓你的桿移動得明顯更多。
調低: 幾乎察覺不到的跟隨。
設定理由: Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply.
Spring response
SpringResponse · Travel enabledTrue
Whether this feature is active in this profile.
設定理由: Applies the configured pitch and roll spring travel curves.
SpringResponse · Output1
設定理由: Sets response at the second pitch-curve point; it is an endpoint only if its input position is full travel.
SpringResponse · Output0.3
設定理由: Sets response at the second roll-curve point; its input position and other points determine the travel law.
Stick feel
StickFeel · Trim feel enabledFalse
Whether this feature is active in this profile.
設定理由: Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
StickFeel · Trim relief enabledFalse
Whether this feature is active in this profile.
設定理由: Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
StickFeel · Force trim enabledFalse
Whether this feature is active in this profile.
設定理由: Enables local force trim, separate from aircraft-owned trim and add-on integration qualification.
StickFeel · G load enabledFalse
Whether this feature is active in this profile.
設定理由: Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it.
StickFeel · Rate damping enabledFalse
Whether this feature is active in this profile.
設定理由: Enables rate damping with the configured coefficients and control law.
Autopilot
Autopilot · Follow enabledFalse
Whether this feature is active in this profile.
設定理由: Autopilot following is off; the configured spring and load retain the hardware feel. Separate neutral hold is on at strength 0.28, when a supported autopilot state admits it.
Autopilot · Neutral hold enabledTrue
Whether this feature is active in this profile.
設定理由: Permits centering hold during a supported AP state, separate from following a moving target.
Autopilot · Neutral hold strength0.28
設定理由: Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled.
Aero
Aero · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions.
Aero · Max flap index4
Where this effect reaches full strength (or has fully faded, for washouts).
調高: a more gradual build to a later peak.
調低: a quicker build.
設定理由: Sets the final flap index for detent normalization. UP plus three detents uses maximum index3.
Aero · Min flap index2
Where this effect begins fading in.
調高: the effect begins later.
調低: it begins earlier.
設定理由: Sets the first flap detent that admits buffet; this is a handle index, not degrees.
Aero · Shaker enabledFalse
Whether this feature is active in this profile.
設定理由: Permits shaker at supported warning conditions; the switch does not establish aircraft equipment.
Ground
Ground · EnabledFalse
Whether this feature is active in this profile.
設定理由: Enables ground effects; each still needs its own strength and contact or motion telemetry.
Engine
Engine · EnabledFalse
Whether this feature is active in this profile.
設定理由: Enables engine cues with nonzero settings and valid running-engine telemetry.
Mechanical
Mechanical · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables accessory cues with configured strengths and observed accessory movement.
Mechanical · Gain0
The strength of this effect.
調高: a stronger effect.
調低: a weaker one.
設定理由: Sets texture from observed gear movement, separate from aerodynamic and touchdown effects.
全部設定檔設定
| 引數 | 數值 | 控制作用及原因 |
|---|---|---|
| Spring strength | 0.55 | Fixed sidestick centering represents the Airbus control arrangement while keeping aircraft control-law behavior separate from hardware resistance. The baseline spring is 0.55. Low-speed spring blending is off. |
| Spring deadband | 0.01 | Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner. |
| Forces · Center starting force | 0.03 | The centre preload is 0.03. It ramps outside the 0.01 deadband across 0.05 travel, shaping the passive centre independently of aircraft autotrim. |
| Forces · Center starting force transition | 0.05 | Sets the travel used to ramp in centre preload. Wider intervals make its onset more gradual. |
| Force gain | 0.24 | The stored 0.24 aerodynamic-load gain is inactive under the fixed-centre control law. |
| Master gain | 0.85 | Scales overall profile strength while preserving effect balance, subject to device and output limits. |
| Dynamic-pressure blend | False | Allows baseline spring strength to rise with indicated airspeed where the control law permits it. |
| Minimum spring factor | 0.55 | Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength. |
| Spring wake-up speed | 20 kt | Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit. |
| Spring full-strength speed | 70 kt | Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| 力回饋調校速度 | 250 kt | Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
| Airspeed spring stiffening | 0 | Adds permitted spring resistance above the full-blend speed. Zero removes this high-speed increase. |
| Airspeed stiffening cap | 2 | Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap. |
| Aileron force scale | 0.65 | Roll and pitch aerodynamic scales are 0.65 and 0.86, respectively. These stored weights do not create directed aerodynamic loading while that term is inactive. The pitch spring-travel curve reaches output 1 at input 1. The roll spring-travel curve reaches output 0.3 at input 1. Spring-travel response contributes separately to axis balance. |
| Elevator force scale | 0.86 | Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Maximum output force | 0.55 | Caps directed-force output. Native spring effects and device limits remain separate. |
| SpringResponse · Travel enabled | True | Applies the configured pitch and roll spring travel curves. |
| SpringResponse · Output | 1 | Sets response at the second pitch-curve point; it is an endpoint only if its input position is full travel. |
| SpringResponse · Output | 0.3 | Sets response at the second roll-curve point; its input position and other points determine the travel law. |
| StickFeel · Trim feel enabled | False | Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| StickFeel · Trim relief enabled | False | Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| StickFeel · Elevator authority | 0 | Aircraft automatic trim is independent of the selected passive stick centre; the trim-tank arrangement is not a hardware trim command. Pitch relief is off, with stored authority 0; roll authority is 0. |
| StickFeel · Aileron authority | 0 | Scales supported roll-trim relief and permitted centre movement. Zero removes roll response. |
| StickFeel · Force trim enabled | False | Enables local force trim, separate from aircraft-owned trim and add-on integration qualification. |
| StickFeel · G load enabled | False | Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it. |
| StickFeel · Rate damping enabled | False | Enables rate damping with the configured coefficients and control law. |
| Autopilot · Follow enabled | False | Autopilot following is off; the configured spring and load retain the hardware feel. Separate neutral hold is on at strength 0.28, when a supported autopilot state admits it. |
| Autopilot · Follow authority | 0.05 | Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply. |
| Autopilot · Neutral hold enabled | True | Permits centering hold during a supported AP state, separate from following a moving target. |
| Autopilot · Neutral hold strength | 0.28 | Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled. |
| Aero · Enabled | True | Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions. |
| Aero · Gain | 0.06 | Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings. |
| Aero · Gain | 0.06 | Sets high-Mach buffet strength; onset and full-strength thresholds are separate. |
| Aero · Gain | 0 | Sets flap buffet at the configured position and speed gates. Flap movement texture is separate. |
| Aero · Max flap index | 4 | Sets the final flap index for detent normalization. UP plus three detents uses maximum index3. |
| Aero · Min flap index | 2 | Sets the first flap detent that admits buffet; this is a handle index, not degrees. |
| Aero · Gain | 0 | Sets gear aerodynamic buffet; movement and ground-contact cues are separate. |
| Aero · Shaker enabled | False | Permits shaker at supported warning conditions; the switch does not establish aircraft equipment. |
| Aero · Amplitude | 0.5 | Sets triggered shaker strength; inactive while the shaker feature is disabled. |
| Ground · Enabled | False | Enables ground effects; each still needs its own strength and contact or motion telemetry. |
| Ground · Gain | 0 | Sets rolling texture strength, modified by speed, surface and undercarriage configuration. |
| Ground · Gain | 0 | Sets gear-bump texture during ground motion, separate from touchdown impact. |
| Ground · Gain | 0 | Sets landing-impact strength; landing telemetry and response shape determine the pulse. |
| Ground · Gain | 0 | Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue. |
| Engine · Enabled | False | Enables engine cues with nonzero settings and valid running-engine telemetry. |
| Engine · Gain | 0 | Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration. |
| Mechanical · Enabled | True | Enables accessory cues with configured strengths and observed accessory movement. |
| Mechanical · Gain | 0 | Sets texture from observed flap movement; a command without movement does not establish the cue. |
| Mechanical · Gain | 0 | Sets texture from observed gear movement, separate from aerodynamic and touchdown effects. |
公開來源 25
- Airbus A330Research background · Wikipedia revision 1373820047 · retrieved 2026-09-12
- Cockpit and flight control familiesAirbus cockpit family descriptions; Airbus cockpit commonality, sidestick philosophy; Airbus cockpit commonality
- Airbus A330Airbus A330 family
- Airbus Beluga XLAirbus A330 family
- v1.3.1 README.mdRelease-pinned README,89309799381c8f010f0d98bd810480dd21f45005
- v1.3.1 CHANGELOG.mdRelease1.3.1 changelog,1.3.0 section
- v1.3.1 X-Plane%20A330%20Pilot%20Operating%20Manual.pdfBundled Laminar A330 manual PDF15,18-19,41-43
- Microsoft Flight Simulator aircraft manuals
- MSFS 2024 FAQ and edition aircraft inventory
- Airbus A330-300 POH
- X-Plane 12 Desktop Manual
- X-Plane aircraft and avionics manuals
- A330-900 change log
- A330 900Official developer / designated store catalogue · checked 2026-09-12
- Captain’s log: landing the first Airbus A330 in AntarcticaCarlos Mirpuri · 5 December 2025
- The flight test of Airbus’s refreshed widebody – the A330neoMike Gerzanics · 2019
- Umschulung auf den Airbus A330 – Upgrade für einen KapitänClaus Harder · 5 May 2023
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- Aerosoft Aircraft A330 neoProduct listing captured 28 September 2026; A330-900neo, MSFS 2024
- A330-300Product listing captured 2026-09-24; edition scope from the reviewed catalogue
- A339X A330-900neoProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- JARDesign 330 Airliner -JARDesign-A330Product listing captured 2026-09-30; edition scope from the reviewed catalogue
- Airbus A330-200 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Airbus A330-300 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Airbus A330-900neo exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
社群與糾錯
如果你的真機經驗表明本頁有誤,請在此指正。
飛行員糾錯
飛過這款飛機?糾正本頁。
本頁基於引用資料構建,而真機經驗勝過任何引用。 請引用有誤的主張,並告訴我們真機的實際表現。糾錯 將交由維護者稽核,並納入本研究的下一次修訂。
登入後即可提交糾錯。無需密碼,只需一次性郵件連結。
登入
社群
該機型的社群配置
該機型還沒有社群配置。
調出了自己的風格? 分享一個配置 它就會出現在這裡。