Development milestones
First flight: 27 April 2005 ( 2005-04-27 )
機型庫Airbus A380
Maarten Visser from Capelle aan den IJssel, Nederland · CC BY-SA 2.0 · Emirates A380Airbus A380
A full-length double-deck airliner built for very high passenger capacity.
Airliner設定檔選項：3 個
瞭解飛機
The A380 arranged two passenger decks within a very large four-engine airframe. Its programme targeted heavily travelled routes and major hub airports. The aircraft's wide wing and extensive landing gear reflect the scale of the design.
Airline interiors vary substantially, so a single seating figure does not describe every A380. The simulator products also differ in the cockpit functions and systems they model.
A huge aircraft, a surprisingly light touch
Mark flew an A380 from Toulouse before the 2009 Paris Air Show, joining a demonstration of new braking and traffic-avoidance functions. The cockpit was unusually spacious and quiet, and taxi cameras made keeping the aircraft on the centreline easier than he expected. Takeoff brought an odd mismatch between the speed indicated on the instruments and his muted visual sense of acceleration. Once airborne, small movements of his wrist were enough to guide the large aircraft through banked turns.
On his landing, he kept off the brake pedals while the brake-to-vacate system slowed the aircraft for the selected exit. He also watched demonstrations using artificial traffic targets and an artificially shortened runway entry. These were planned tests, not encounters with real conflicting traffic or an actual runway emergency.
An approachable giant, with room to improve the cockpit
After flying the first A380 test aircraft from Toulouse, Gerzanics told Max Kingsley-Jones that its handling felt closer to an A320 than an A340. Taxi cameras helped him position the nose gear accurately, and the cockpit height and landing-gear geometry made ground manoeuvring less daunting than its enormous wingspan suggested. The aircraft was well below its maximum takeoff weight on this particular evaluation flight.
He found the low-speed handling agile around the airport and the touchdown and lowering of the nose notably smooth. He welcomed larger displays and graphical changes to the flight plan, but his assessment was not unqualified praise: separate controls for the flight-management system, aircraft monitoring and information terminal made the integration less satisfactory than in contemporary business jets.
A dream aircraft, and the work behind every departure
Kashwani had wanted to fly the A380 from its launch, and his opportunity arrived in 2008. On his first walk-around, the scale of its wings and engines left a lasting impression. In Airbus's interview, the Emirates captain describes a responsive aircraft that he considered especially stable among the jetliners he had flown. Seeing people photograph it at takeoff or landing continued to bring back that initial sense of occasion.
His working day was more methodical than the spectacle outside suggested. He liked to reach the aircraft an hour before departure so the large crew had time to prepare, check the systems and receive the passengers. Automation provided support in cruise, while the pilots still had to identify and navigate around thunderstorms. Airbus published the interview with Kashwani.
The emergency continued after the landing
Evans was the supervising check captain in an observer seat when QF32 suffered an uncontained engine failure after departing Singapore on 4 November 2010. He describes a flood of warnings that required the five pilots to establish what still worked, discuss conflicting indications and judge which actions were appropriate. While Richard de Crespigny flew the aircraft and the operating crew worked through the problems, Evans also helped keep passengers informed. The assessment took nearly two hours before the crew returned to land.
For Evans, the period after stopping was particularly worrying. One engine continued running, fuel was leaking and the brakes were hot. The crew weighed an immediate slide evacuation against keeping passengers aboard with the cabin crew ready to act. They eventually disembarked through stairs. He emphasises shared judgement, communication and cabin-crew work during the emergency.
公開來源 12
- Airbus A380Research background · Wikipedia revision 1374387538 · retrieved 2026-09-12
- A380X SOP
- Microsoft Flight Simulator aircraft manuals
- A380 Airliner for MSFS-2024Official developer / designated store catalogue · checked 2026-09-12
- Flying the Airbus A380Robert P. Mark · June 2009
- Flying Airbus’s gentle giant – test-pilot’s first impressionsMike Gerzanics · 18 September 2006
- Behind the scenes with Airbus A380 pilotsAli Kashwani · April 2019
- Exclusive – Qantas QF32 flight from the cockpitDavid Evans · 8 December 2010
- Installer Guide - FlyByWire Simulations DocumentationOfficial developer / designated-store reference · checked 2026-09-14
- INOP System - FlyByWire Simulations DocumentationOfficial developer / designated-store reference · checked 2026-09-14
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- iniBuilds A380 Airliner for MSFS – iniBuilds StoreProduct listing captured 2026-09-30; edition scope from the reviewed catalogue
設定檔如何建模
FlyByWire A380X
Free + ProMSFS 2020MSFS 2024FlyByWire
The A380 arranged two passenger decks within a very large four-engine airframe. Its programme targeted heavily travelled routes and major hub airports. The aircraft's wide wing and extensive landing gear reflect the scale of the design.
This profile selects FlyByWire A380X for MSFS 2020, MSFS 2024.
The spring stays independent of airspeed. Directed aerodynamic loading is omitted.
Pitch-trim relief is off. Autopilot following is off.
此確切修訂版尚未開放公開安裝。
Controls and trim
Airbus describes fully electric pitch trim, including its backup, for the A380; normal-law trim is automatic. Its hydraulic and electric actuator redundancy and gust/load alleviation act on surfaces independently of the sidesticks. iniBuilds distinguishes Trent 900 and GP7200 engines and early/modern software batches. FlyByWire's A380X operating procedures have separate scope from the A32NX systems API.
The selected implementation
The A380X SOP belongs to the A380 implementation. A32NX API identifiers are not assigned to A380X despite related operating philosophy.
About the values
The gains are normalized profile settings. They describe the chosen effect balance; hand force depends on the device and its output limits. IAS references are tuning values rather than operating limits. Physical acceptance of this revision remains pending.
Master gain & control system
Master gain85%
施加於模型產出的一切、在裝置上限之前的最終整體輸出縮放。
調高: 一切(彈簧、載荷、效果)一同增強。
調低: 一切一同變柔。
設定理由: Scales overall profile strength while preserving effect balance, subject to device and output limits.
Forces
Spring strength55%
把搖桿拉回中央的基礎回中力。其他所有力都疊加在它之上。太低,正常飛行中搖桿會發軟;太高,它會與你的手較勁,並掩蓋疊加其上的細微提示。
調高: 更硬的回中,更抗手。
調低: 更軟的桿,只靠氣動載荷。
設定理由: Fixed spring centering represents the passive A380 sidestick; hydraulic/electric surface redundancy does not imply stick backdrive. The baseline spring is 0.55. Low-speed spring blending is off.
Cockpit and flight control familiesA380X SOPA380 Airliner for MSFS-2024A380 FAST special: control architecture and manual pitch trimSpring deadband1%
中央附近彈簧保持安靜的小中立區,讓靜止時的微小移動不會咔嗒作響。更寬更安穩但更松,更窄更精確但可能在中央附近抖動。
調高: 更安靜但更松的中央,曠量更大。
調低: 更緊的中央,靜止時可能抖動。
設定理由: Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner.
Forces · Center starting force0.03
設定理由: The centre preload is 0.03. It ramps outside the 0.01 deadband across 0.05 travel, shaping the passive centre independently of aircraft autotrim.
Forces · Center starting force transition0.05
設定理由: Sets the travel used to ramp in centre preload. Wider intervals make its onset more gradual.
Overall aerodynamic load0%
作用於兩條持續軸載荷的主縮放,在它們各自的獨立平衡之前施加。設定檔通常不動它,而是調校兩條軸載荷。
調高: 兩軸載荷一同加重。
調低: 兩軸一同減輕。
設定理由: The stored 0 aerodynamic-load gain is inactive under the fixed-centre control law.
Airspeed blendingFalse
啟用低速彈簧介入視窗(上面的起始/全強度節數)。關閉時彈簧在所有速度下恆定。
設定理由: Allows baseline spring strength to rise with indicated airspeed where the control law permits it.
Low-speed spring floor50%
在靜止、空速尚未產生氣動力之前,彈簧還剩多少。下限高,停機時搖桿結實;下限低,則是停放輕型飛機那種鋼索鬆弛的感覺。
調高: 停機和滑行時桿更結實。
調低: 停機時桿發軟,只隨速度甦醒。
設定理由: Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength.
Spring engagement start8 kt
彈簧從低速下限開始向全強度攀升的空速:起飛滑跑中操縱面"甦醒"的那一刻。
設定理由: Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit.
Spring engagement full65 kt
彈簧達到全強度的空速。從起點到這裡,隨著氣流在操縱面上增強,回中逐漸變硬。
設定理由: Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
力回饋調校速度250
氣動載荷達到設計滿值的指示空速。它把整條載荷曲線錨定在飛機真實的速度範圍:172在110節就載滿,噴氣機要晚得多。
調高: 載荷來得更晚;桿輕到更高速度。
調低: 載荷來得更早,巡航更沉。
設定理由: Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Centre firmness vs speed0%
在偏轉載荷之外,回中本身隨速度變硬的程度。零則中央手感恆定;越大,巡航時回中越硬,起落航線上越松。
調高: 中央隨速度明顯變硬。
調低: 任何速度下中央手感恆定。
設定理由: Adds permitted spring resistance above the full-blend speed. Zero removes this high-speed increase.
Centre stiffening cap5
速度驅動的中央變硬上限,防止高速飛行把彈簧無限上緊。
調高: 高速允許更多總硬化。
調低: 硬化更早封頂。
設定理由: Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap.
Aileron load72%
由副翼偏轉和空速產生的持續橫滾載荷,獨立於俯仰調校。與升降舵載荷一起,決定評測中常說的操縱協調比。
調高: 橫滾力更重。
調低: 副翼更輕更靈。
設定理由: Roll and pitch aerodynamic scales are 0.72 and 1, respectively. These stored weights do not create directed aerodynamic loading while that term is inactive. The pitch spring-travel curve reaches output 1 at input 1. The roll spring-travel curve reaches output 0.3 at input 1. Spring-travel response contributes separately to axis balance.
Elevator load100%
由升降舵偏轉和空速產生的持續俯仰載荷,獨立於橫滾調校。這是決定機型俯仰重量的主槓桿。它不影響副翼、彈簧、配平或抖振力。
調高: 速度下持續俯仰力更重。
調低: 升降舵更輕,握持更省力。
設定理由: Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Max output force55%
每個穩態俯仰或橫滾力到達裝置前的上限,防止猛烈機動中砸擊或飽和硬體。
調高: 削波前更高的穩態力峰值。
調低: 更柔的上限;猛烈機動更早被抹平。
設定理由: Caps directed-force output. Native spring effects and device limits remain separate.
Trim
Trim relief (elevator)0%
升降舵配平緩解持續俯仰力、移動桿的安定位置的強度。在100 %時,配平得當的飛機不需要保持壓力——正是真實飛行中"用配平消掉載荷"的流程。
調高: 配平消掉更多持續力;100 %時滿配平可完全抵消。
調低: 即使配平也仍要持續用力。
設定理由: Automatic aircraft trim and the absence of a mechanical trim wheel keep hardware-centre movement separate from stabilizer operation. Pitch relief is off, with stored authority 0; roll authority is 0.
Cockpit and flight control familiesA380X SOPA380 Airliner for MSFS-2024A380 FAST special: control architecture and manual pitch trimTrim relief (aileron)0%
橫滾配平的同類緩解。多數通航機型沒有真正的副翼配平,所以保持為零;有橫滾配平的機型獲得相應的值。
調高: 橫滾配平消掉更多持續力。
調低: 橫滾配平作用更小。
設定理由: Scales supported roll-trim relief and permitted centre movement. Zero removes roll response.
Effect gains · Ground
Runway rumble0%
由輪速和地面型別(鋪裝、草地、礫石)產生的滾動振動。
調高: 桿上更強的地面質感。
調低: 更平滑的滑行。
設定理由: Sets rolling texture strength, modified by speed, surface and undercarriage configuration.
Gear bumps0%
來自伸縮縫、車轍和粗糙地面的短促離散顛簸,為持續隆隆聲打上標點。
調高: 接縫與車轍的衝擊更清晰。
調低: 更柔的地面細節。
設定理由: Sets gear-bump texture during ground motion, separate from touchdown impact.
Effect gains · Airframe
Stall buffet6%
接近失速及失速警告響起時的機體抖動:這副機翼宣告不滿的音量。斷失乾脆的機型抖振收斂,讓喇叭承擔警告。
調高: 更強的失速前顫抖。
調低: 更含蓄的機翼;警告交給喇叭。
設定理由: Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings.
Mach buffet6%
接近馬赫極限的跨音速抖振。對接近MMO的噴氣機有意義,對到不了那裡的活塞機和渦槳機為零。
調高: 接近馬赫極限時更強的跨音速抖振。
調低: 高馬赫下更平滑的飛行。
設定理由: Sets high-Mach buffet strength; onset and full-strength thresholds are separate.
Flap buffet0%
襟翼伸入氣流後機體的低頻振動,發生在它們真正做功的速度視窗內。
調高: 襟翼做功時更粗糙的飛行。
調低: 更柔的進近襟翼。
設定理由: Sets flap buffet at the configured position and speed gates. Flap movement texture is separate.
Gear buffet0%
可收放起落架懸在氣流中引起的機體鼓振。固定起落架機型為零,它們的機體外形從不改變。
調高: 放起落架時更多鼓振。
調低: 放起落架飛行更乾淨。
設定理由: Sets gear aerodynamic buffet; movement and ground-contact cues are separate.
Stick shaker50%
由飛機自身失速警告系統觸發的專用抖桿器振動。只有真有抖桿器的機型才有值;其餘全靠氣動抖振和喇叭。
調高: 更硬的抖桿器。
調低: 更含蓄的抖桿器。
設定理由: Sets triggered shaker strength; inactive while the shaker feature is disabled.
Effect gains · Engine, mechanical & drag
Touchdown thump0%
機輪觸及跑道那一下的單次衝擊,按下沉率縮放:輕柔著陸是耳語,結實到達是一記悶響。
調高: 觸地時更硬的一擊。
調低: 更柔的到達。
設定理由: Sets landing-impact strength; landing telemetry and response shape determine the pulse.
Reverse rumble0%
反推或槳葉beta區工作時的滑跑振動。無反推機型為零。
調高: 反推下更粗糙的滑跑。
調低: 更含蓄的反推。
設定理由: Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue.
Engine rumble0%
從慢車到全功率跟隨轉速的持續動力裝置振動——前方有東西在燒油的永恆提醒。
調高: 桿裡更多引擎。
調低: 更含蓄的引擎。
設定理由: Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration.
Flap motion0%
僅在模擬器報告襟翼舵面確實移動時的持續振動。它跟隨真實作動器的運動和故障,而非估算的計時器。
調高: 襟翼移動中更多振動。
調低: 更含蓄的襟翼行程。
設定理由: Sets texture from observed flap movement; a command without movement does not establish the cue.
Autopilot follow
AP follow authority5%
自動駕駛指令可以讓桿實際移動多遠。在MSFS中保持極小,因為移動的軸可能被讀回為飛行員輸入;零則完全停用跟隨。
調高: 自動駕駛讓你的桿移動得明顯更多。
調低: 幾乎察覺不到的跟隨。
設定理由: Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply.
Spring response
SpringResponse · Travel enabledTrue
Whether this feature is active in this profile.
設定理由: Applies the configured pitch and roll spring travel curves.
SpringResponse · Output1
設定理由: Sets response at the second pitch-curve point; it is an endpoint only if its input position is full travel.
SpringResponse · Output0.3
設定理由: Sets response at the second roll-curve point; its input position and other points determine the travel law.
Stick feel
StickFeel · Trim feel enabledFalse
Whether this feature is active in this profile.
設定理由: Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
StickFeel · Trim relief enabledFalse
Whether this feature is active in this profile.
設定理由: Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
StickFeel · Force trim enabledFalse
Whether this feature is active in this profile.
設定理由: Enables local force trim, separate from aircraft-owned trim and add-on integration qualification.
StickFeel · G load enabledFalse
Whether this feature is active in this profile.
設定理由: Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it.
StickFeel · Rate damping enabledFalse
Whether this feature is active in this profile.
設定理由: Enables rate damping with the configured coefficients and control law.
Autopilot
Autopilot · Follow enabledFalse
Whether this feature is active in this profile.
設定理由: Autopilot following is off; the configured spring and load retain the hardware feel. Separate neutral hold is on at strength 0.28, when a supported autopilot state admits it.
Autopilot · Neutral hold enabledTrue
Whether this feature is active in this profile.
設定理由: Permits centering hold during a supported AP state, separate from following a moving target.
Autopilot · Neutral hold strength0.28
設定理由: Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled.
Aero
Aero · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions.
Aero · Max flap index4
Where this effect reaches full strength (or has fully faded, for washouts).
調高: a more gradual build to a later peak.
調低: a quicker build.
設定理由: Sets the final flap index for detent normalization. UP plus three detents uses maximum index3.
Aero · Min flap index2
Where this effect begins fading in.
調高: the effect begins later.
調低: it begins earlier.
設定理由: Sets the first flap detent that admits buffet; this is a handle index, not degrees.
Aero · Shaker enabledFalse
Whether this feature is active in this profile.
設定理由: Permits shaker at supported warning conditions; the switch does not establish aircraft equipment.
Ground
Ground · EnabledFalse
Whether this feature is active in this profile.
設定理由: Enables ground effects; each still needs its own strength and contact or motion telemetry.
Engine
Engine · EnabledFalse
Whether this feature is active in this profile.
設定理由: Enables engine cues with nonzero settings and valid running-engine telemetry.
Mechanical
Mechanical · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables accessory cues with configured strengths and observed accessory movement.
Mechanical · Gain0
The strength of this effect.
調高: a stronger effect.
調低: a weaker one.
設定理由: Sets texture from observed gear movement, separate from aerodynamic and touchdown effects.
全部設定檔設定
| 引數 | 數值 | 控制作用及原因 |
|---|---|---|
| Spring strength | 0.55 | Fixed spring centering represents the passive A380 sidestick; hydraulic/electric surface redundancy does not imply stick backdrive. The baseline spring is 0.55. Low-speed spring blending is off. |
| Spring deadband | 0.01 | Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner. |
| Forces · Center starting force | 0.03 | The centre preload is 0.03. It ramps outside the 0.01 deadband across 0.05 travel, shaping the passive centre independently of aircraft autotrim. |
| Forces · Center starting force transition | 0.05 | Sets the travel used to ramp in centre preload. Wider intervals make its onset more gradual. |
| Force gain | 0 | The stored 0 aerodynamic-load gain is inactive under the fixed-centre control law. |
| Master gain | 0.85 | Scales overall profile strength while preserving effect balance, subject to device and output limits. |
| Dynamic-pressure blend | False | Allows baseline spring strength to rise with indicated airspeed where the control law permits it. |
| Minimum spring factor | 0.5 | Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength. |
| Spring wake-up speed | 8 kt | Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit. |
| Spring full-strength speed | 65 kt | Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| 力回饋調校速度 | 250 kt | Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
| Airspeed spring stiffening | 0 | Adds permitted spring resistance above the full-blend speed. Zero removes this high-speed increase. |
| Airspeed stiffening cap | 5 | Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap. |
| Aileron force scale | 0.72 | Roll and pitch aerodynamic scales are 0.72 and 1, respectively. These stored weights do not create directed aerodynamic loading while that term is inactive. The pitch spring-travel curve reaches output 1 at input 1. The roll spring-travel curve reaches output 0.3 at input 1. Spring-travel response contributes separately to axis balance. |
| Elevator force scale | 1 | Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Maximum output force | 0.55 | Caps directed-force output. Native spring effects and device limits remain separate. |
| SpringResponse · Travel enabled | True | Applies the configured pitch and roll spring travel curves. |
| SpringResponse · Output | 1 | Sets response at the second pitch-curve point; it is an endpoint only if its input position is full travel. |
| SpringResponse · Output | 0.3 | Sets response at the second roll-curve point; its input position and other points determine the travel law. |
| StickFeel · Trim feel enabled | False | Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| StickFeel · Trim relief enabled | False | Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| StickFeel · Elevator authority | 0 | Automatic aircraft trim and the absence of a mechanical trim wheel keep hardware-centre movement separate from stabilizer operation. Pitch relief is off, with stored authority 0; roll authority is 0. |
| StickFeel · Aileron authority | 0 | Scales supported roll-trim relief and permitted centre movement. Zero removes roll response. |
| StickFeel · Force trim enabled | False | Enables local force trim, separate from aircraft-owned trim and add-on integration qualification. |
| StickFeel · G load enabled | False | Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it. |
| StickFeel · Rate damping enabled | False | Enables rate damping with the configured coefficients and control law. |
| Autopilot · Follow enabled | False | Autopilot following is off; the configured spring and load retain the hardware feel. Separate neutral hold is on at strength 0.28, when a supported autopilot state admits it. |
| Autopilot · Follow authority | 0.05 | Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply. |
| Autopilot · Neutral hold enabled | True | Permits centering hold during a supported AP state, separate from following a moving target. |
| Autopilot · Neutral hold strength | 0.28 | Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled. |
| Aero · Enabled | True | Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions. |
| Aero · Gain | 0.06 | Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings. |
| Aero · Gain | 0.06 | Sets high-Mach buffet strength; onset and full-strength thresholds are separate. |
| Aero · Gain | 0 | Sets flap buffet at the configured position and speed gates. Flap movement texture is separate. |
| Aero · Max flap index | 4 | Sets the final flap index for detent normalization. UP plus three detents uses maximum index3. |
| Aero · Min flap index | 2 | Sets the first flap detent that admits buffet; this is a handle index, not degrees. |
| Aero · Gain | 0 | Sets gear aerodynamic buffet; movement and ground-contact cues are separate. |
| Aero · Shaker enabled | False | Permits shaker at supported warning conditions; the switch does not establish aircraft equipment. |
| Aero · Amplitude | 0.5 | Sets triggered shaker strength; inactive while the shaker feature is disabled. |
| Ground · Enabled | False | Enables ground effects; each still needs its own strength and contact or motion telemetry. |
| Ground · Gain | 0 | Sets rolling texture strength, modified by speed, surface and undercarriage configuration. |
| Ground · Gain | 0 | Sets gear-bump texture during ground motion, separate from touchdown impact. |
| Ground · Gain | 0 | Sets landing-impact strength; landing telemetry and response shape determine the pulse. |
| Ground · Gain | 0 | Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue. |
| Engine · Enabled | False | Enables engine cues with nonzero settings and valid running-engine telemetry. |
| Engine · Gain | 0 | Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration. |
| Mechanical · Enabled | True | Enables accessory cues with configured strengths and observed accessory movement. |
| Mechanical · Gain | 0 | Sets texture from observed flap movement; a command without movement does not establish the cue. |
| Mechanical · Gain | 0 | Sets texture from observed gear movement, separate from aerodynamic and touchdown effects. |
公開來源 17
- Airbus A380Research background · Wikipedia revision 1374387538 · retrieved 2026-09-12
- Cockpit and flight control familiesAirbus cockpit family descriptions; Airbus cockpit commonality, sidestick philosophy; Airbus cockpit commonality
- A380X SOPA380X standard operating procedures, control and autoflight flows
- A380 Airliner for MSFS-2024System features, productversion and requirementsOfficial developer / designated store catalogue · checked 2026-09-12
- A380 FAST special: control architecture and manual pitch trimAirbusFASTNovember2016PDF pp22,45
- Sidestick controlsSidesticks section, revised 2026-08-31
- Simulator edition downloadsDownloads grouped by Microsoft Flight Simulator 2020 and 2024
- A32NX systems APIATA 27 and FCDC discrete words
- Microsoft Flight Simulator aircraft manuals
- Flying the Airbus A380Robert P. Mark · June 2009
- Flying Airbus’s gentle giant – test-pilot’s first impressionsMike Gerzanics · 18 September 2006
- Behind the scenes with Airbus A380 pilotsAli Kashwani · April 2019
- Exclusive – Qantas QF32 flight from the cockpitDavid Evans · 8 December 2010
- Installer Guide - FlyByWire Simulations DocumentationOfficial developer / designated-store reference · checked 2026-09-14
- INOP System - FlyByWire Simulations DocumentationOfficial developer / designated-store reference · checked 2026-09-14
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- iniBuilds A380 Airliner for MSFS – iniBuilds StoreProduct listing captured 2026-09-30; edition scope from the reviewed catalogue
社群與糾錯
如果你的真機經驗表明本頁有誤,請在此指正。
飛行員糾錯
飛過這款飛機?糾正本頁。
本頁基於引用資料構建,而真機經驗勝過任何引用。 請引用有誤的主張,並告訴我們真機的實際表現。糾錯 將交由維護者稽核,並納入本研究的下一次修訂。
登入後即可提交糾錯。無需密碼,只需一次性郵件連結。
登入
社群
該機型的社群配置
該機型還沒有社群配置。
調出了自己的風格? 分享一個配置 它就會出現在這裡。