Development milestones
First flight: 5 November 1997
Developed from: Diamond DA20
機型庫Diamond DA40
bomberpilot · CC BY-SA 2.0 · Diamond DA40 Diamond Star picturedDiamond DA40
Mechanical stick controls with aerodynamic pitch trim and separately tuned pitch and roll resistance.
General aviationDA40設定檔選項：10 個
瞭解飛機
The DA40 took the DA20's general concept into a larger cabin. Its low wing, fixed tricycle undercarriage and extensive canopy glazing give it a distinctive appearance. Production has taken place in Austria and Canada, with several engine and equipment developments.
Petrol-engined and diesel-family DA40s differ in engine management and cockpit equipment. The simulator products identify their represented model.
Diamond DA40 NG
- Powerplant
- Austro AE 300 turbodiesel, 168 hp↗
- Seats
- 4↗
- Max takeoff weight
- 2,888 lb (1,310 kg)↗
- Wingspan
- 38 ft 2 in (11.63 m)↗
- Length
- 26 ft 5 in (8.06 m)↗
- Never exceed (Vne)
- 178 KIAS↗
- Maneuvering (Va)
- 108 KIAS at MTOW↗
- Stall, landing config (Vs0)
- ≈49 KCAS↗
- Max cruise
- ≈154 KTAS↗
- Service ceiling
- 16,400 ft↗
- Range
- ≈940 nm at economy cruise↗
- Usable fuel
- ≈39 US gal Jet A↗
Familiar fine handling, with a qualified verdict on the diesel
Whiteman approached the Austro-powered DA40 NG with experience of the original prototype and earlier production versions. Flying G-SUEO with its regular demonstration pilot, Mark, he appreciated the simple power control and comfortable seating, although mastering the Garmin displays would require more study. Initial acceleration was strong, but the departure did not deliver the improvement he had hoped for. Retracting the flaps brought a noticeable reduction in the modest early climb.
Once established, the familiar appeal returned: light, well-coordinated controls, a useful mechanical trimwheel and excellent visibility made formation flying and general manoeuvring a pleasure. The aeroplane required continuing right-pedal pressure, which Mark suspected might reflect that particular aircraft's rigging; Whiteman did not establish it as a fleet characteristic. His final assessment remained mixed. He admired the DA40's handling and recognised the diesel's potential economy, while wishing its takeoff and initial climb felt more convincing.
A trainer that rewards coordination and planning
Turner evaluated the DA40 as a prospective training aircraft and found plenty to keep a student engaged. Its low seating position and broad view made the runway feel close, while the initial takeoff required deliberate directional control. In the air, he found the stick easy to adopt and the controls light without becoming vague. Once properly trimmed, the aircraft held its attitude well, but its clean airframe demanded anticipation when levelling off or preparing to descend.
An overcast formed beneath the demonstration flight, so the return included an IFR clearance and vectors to an ILS. That gave Turner a practical opportunity to explore the workload of an instrument approach before breaking into visual conditions for landing. He finished the flight smiling and considered the Diamond a promising trainer for future professional pilots. His praise included the demands it placed on rudder coordination and energy management, alongside reservations about ground ventilation, storage space and the attention required during transition.
Dinner at Santa Paula changes a traditional pilot’s mind
Lee wanted to experience the DA40 XLS on an ordinary outing, so he joined distributor demonstration pilot Robert Stewart for a trip from Long Beach to Santa Paula. The wraparound view immediately impressed him, and he welcomed the manual trimwheel after initially fumbling with electric trim. Climbing out toward the coast, he began to appreciate how much of the surrounding landscape was visible from ahead of the wing.
The journey combined low-speed handling demonstrations, music through the headsets and a look at the Garmin synthetic-vision display before an arrival among Santa Paula's classic aircraft. Lee had expected to dislike a modern composite aeroplane, but found that the technology left plenty of opportunity to enjoy hand-flying. Returning to Long Beach, he was reluctant to walk away.
公開來源 16
- Diamond DA40 Diamond StarResearch background · Wikipedia revision 1373674831 · retrieved 2026-09-12
- Microsoft Flight Simulator aircraft manuals
- MSFS 2024 FAQ and edition aircraft inventory
- MSFS 2020 FAQ and edition aircraft inventory
- Flight test: Diamond DA40 NGPhilip Whiteman · 12 June 2015
- Diamond DA40: Airline Pilot Trainer, Part IIThomas Turner · 27 November 2004
- DA 40 XLS: The Innovator Keeps Getting BetterMarc C. Lee · 24 February 2009
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- COWS | DA40 SeriesProduct listing captured 2026-09-30; edition scope from the reviewed catalogue
- DA40 Expansion PackProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Take Command!: RealSimGear DA40NG, X-AviationProduct listing captured 2026-09-23; edition scope from the reviewed catalogue
- Diamond DA40NG-SimSolutions-DA40Product listing captured 2026-09-23; edition scope from the reviewed catalogue
- Diamond DA40-180 Diamond StarProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Diamond DA40 NG AFM紙質或存檔參考資料；無公開連結
- EASA TCDS A.022紙質或存檔參考資料；無公開連結
- Diamond published data紙質或存檔參考資料；無公開連結
設定檔如何建模
Diamond DA40 NG
Free + ProMSFS 2024MSFS 2020
The DA40 took the DA20's general concept into a larger cabin. Its low wing, fixed tricycle undercarriage and extensive canopy glazing give it a distinctive appearance. Production has taken place in Austria and Canada, with several engine and equipment developments.
The factory starting point selects Diamond DA40 NG across MSFS 2024, MSFS 2020.
Mechanical linkage motivates airspeed-sensitive stick resistance. Spring resistance builds with the selected airspeed response. A separate aerodynamic term adds speed-dependent control load.
The DA40 elevator tab supplies pitch pressure relief, unlike the DA20’s spring-preload system. Valid trim provides the configured pressure relief. Autopilot following is enabled for supported control references.
此確切修訂版尚未開放公開安裝。
Controls and trim
The DA40’s elevator and ailerons use pushrods, with cables operating the rudder. A Bowden cable drives the elevator trim tab, and electric flaps select their named positions. Lycoming XLS and diesel NG versions retain different propulsion and cockpit equipment.
About the values
The gains are normalized profile settings. They describe the chosen effect balance; hand force depends on the device and its output limits. IAS references are tuning values rather than operating limits. Physical acceptance of this revision remains pending.
Master gain & control system
Master gain85%
施加於模型產出的一切、在裝置上限之前的最終整體輸出縮放。
調高: 一切(彈簧、載荷、效果)一同增強。
調低: 一切一同變柔。
設定理由: Scales overall profile strength while preserving effect balance, subject to device and output limits.
Forces
Spring strength80%
把搖桿拉回中央的基礎回中力。其他所有力都疊加在它之上。太低,正常飛行中搖桿會發軟;太高,它會與你的手較勁,並掩蓋疊加其上的細微提示。
調高: 更硬的回中,更抗手。
調低: 更軟的桿,只靠氣動載荷。
設定理由: Mechanical linkage motivates airspeed-sensitive stick resistance. The baseline spring is 0.8. Its low-speed blend reaches baseline strength at 67 KIAS.
Exact product and documentation researchDA40 Expansion PackDiamond-authored DA40NG AFM archived copyDiamond official DA40NG G1000 legacy checklist 21.0Publisher DA40NG v1.2.0 current compatibility and trim changesRealSimGear separate NXi option and aircraft compatibilityDiamond DA40NG-SimSolutions-DA40Diamond DA40-180 Diamond StarDiamond DA40 technical specificationsDA40-180 Diamond StarFlight test: Diamond DA40 NGDA 40 XLS: The Innovator Keeps Getting BetterBuying a Used Aircraft: Diamond DA40 StarSpring deadband4%
中央附近彈簧保持安靜的小中立區,讓靜止時的微小移動不會咔嗒作響。更寬更安穩但更松,更窄更精確但可能在中央附近抖動。
調高: 更安靜但更松的中央,曠量更大。
調低: 更緊的中央,靜止時可能抖動。
設定理由: Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner.
Overall aerodynamic load70%
作用於兩條持續軸載荷的主縮放,在它們各自的獨立平衡之前施加。設定檔通常不動它,而是調校兩條軸載荷。
調高: 兩軸載荷一同加重。
調低: 兩軸一同減輕。
設定理由: The aerodynamic-load gain is 0.7 with an indicated-speed reference of 125 KIAS. This supplies speed-dependent loading alongside the spring.
Spring engagement full67 kt
彈簧達到全強度的空速。從起點到這裡,隨著氣流在操縱面上增強,回中逐漸變硬。
設定理由: Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
Centre firmness vs speed15%
在偏轉載荷之外,回中本身隨速度變硬的程度。零則中央手感恆定;越大,巡航時回中越硬,起落航線上越松。
調高: 中央隨速度明顯變硬。
調低: 任何速度下中央手感恆定。
設定理由: The high-speed spring-stiffening gain is 0.15. It strengthens the permitted spring response above 67 KIAS, with the squared-speed ratio capped at 5.
Centre stiffening cap5
速度驅動的中央變硬上限,防止高速飛行把彈簧無限上緊。
調高: 高速允許更多總硬化。
調低: 硬化更早封頂。
設定理由: Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap.
Aileron load85%
由副翼偏轉和空速產生的持續橫滾載荷,獨立於俯仰調校。與升降舵載荷一起,決定評測中常說的操縱協調比。
調高: 橫滾力更重。
調低: 副翼更輕更靈。
設定理由: Roll and pitch aerodynamic scales are 0.85 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled.
Elevator load100%
由升降舵偏轉和空速產生的持續俯仰載荷,獨立於橫滾調校。這是決定機型俯仰重量的主槓桿。它不影響副翼、彈簧、配平或抖振力。
調高: 速度下持續俯仰力更重。
調低: 升降舵更輕,握持更省力。
設定理由: Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Max output force55%
每個穩態俯仰或橫滾力到達裝置前的上限,防止猛烈機動中砸擊或飽和硬體。
調高: 削波前更高的穩態力峰值。
調低: 更柔的上限;猛烈機動更早被抹平。
設定理由: Caps directed-force output. Native spring effects and device limits remain separate.
Airspeed blendingTrue
啟用低速彈簧介入視窗(上面的起始/全強度節數)。關閉時彈簧在所有速度下恆定。
設定理由: Allows baseline spring strength to rise with indicated airspeed where the control law permits it.
Low-speed spring floor50%
在靜止、空速尚未產生氣動力之前,彈簧還剩多少。下限高,停機時搖桿結實;下限低,則是停放輕型飛機那種鋼索鬆弛的感覺。
調高: 停機和滑行時桿更結實。
調低: 停機時桿發軟,只隨速度甦醒。
設定理由: Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength.
Spring engagement start15 kt
彈簧從低速下限開始向全強度攀升的空速:起飛滑跑中操縱面"甦醒"的那一刻。
設定理由: Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit.
力回饋調校速度125
氣動載荷達到設計滿值的指示空速。它把整條載荷曲線錨定在飛機真實的速度範圍:172在110節就載滿,噴氣機要晚得多。
調高: 載荷來得更晚;桿輕到更高速度。
調低: 載荷來得更早,巡航更沉。
設定理由: Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Trim
Trim relief (elevator)30%
升降舵配平緩解持續俯仰力、移動桿的安定位置的強度。在100 %時,配平得當的飛機不需要保持壓力——正是真實飛行中"用配平消掉載荷"的流程。
調高: 配平消掉更多持續力;100 %時滿配平可完全抵消。
調低: 即使配平也仍要持續用力。
設定理由: The DA40 elevator tab supplies pitch pressure relief, unlike the DA20’s spring-preload system. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0.
Exact product and documentation researchDA40 Expansion PackDiamond-authored DA40NG AFM archived copyDiamond official DA40NG G1000 legacy checklist 21.0Publisher DA40NG v1.2.0 current compatibility and trim changesRealSimGear separate NXi option and aircraft compatibilityDiamond DA40NG-SimSolutions-DA40Diamond DA40-180 Diamond StarDiamond DA40 technical specificationsDA40-180 Diamond StarFlight test: Diamond DA40 NGDA 40 XLS: The Innovator Keeps Getting BetterBuying a Used Aircraft: Diamond DA40 StarTrim relief (aileron)0%
橫滾配平的同類緩解。多數通航機型沒有真正的副翼配平,所以保持為零;有橫滾配平的機型獲得相應的值。
調高: 橫滾配平消掉更多持續力。
調低: 橫滾配平作用更小。
設定理由: Scales supported roll-trim relief and permitted centre movement. Zero removes roll response.
Effect gains · Ground
Runway rumble38%
由輪速和地面型別(鋪裝、草地、礫石)產生的滾動振動。
調高: 桿上更強的地面質感。
調低: 更平滑的滑行。
設定理由: Sets rolling texture strength, modified by speed, surface and undercarriage configuration.
Gear bumps25%
來自伸縮縫、車轍和粗糙地面的短促離散顛簸,為持續隆隆聲打上標點。
調高: 接縫與車轍的衝擊更清晰。
調低: 更柔的地面細節。
設定理由: Sets gear-bump texture during ground motion, separate from touchdown impact.
Effect gains · Airframe
Stick shaker50%
由飛機自身失速警告系統觸發的專用抖桿器振動。只有真有抖桿器的機型才有值;其餘全靠氣動抖振和喇叭。
調高: 更硬的抖桿器。
調低: 更含蓄的抖桿器。
設定理由: Sets triggered shaker strength; inactive while the shaker feature is disabled.
Stall buffet50%
接近失速及失速警告響起時的機體抖動:這副機翼宣告不滿的音量。斷失乾脆的機型抖振收斂,讓喇叭承擔警告。
調高: 更強的失速前顫抖。
調低: 更含蓄的機翼;警告交給喇叭。
設定理由: Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings.
Mach buffet0%
接近馬赫極限的跨音速抖振。對接近MMO的噴氣機有意義,對到不了那裡的活塞機和渦槳機為零。
調高: 接近馬赫極限時更強的跨音速抖振。
調低: 高馬赫下更平滑的飛行。
設定理由: Sets high-Mach buffet strength; onset and full-strength thresholds are separate.
Flap buffet28%
襟翼伸入氣流後機體的低頻振動,發生在它們真正做功的速度視窗內。
調高: 襟翼做功時更粗糙的飛行。
調低: 更柔的進近襟翼。
設定理由: Sets flap buffet at the configured position and speed gates. Flap movement texture is separate.
Gear buffet0%
可收放起落架懸在氣流中引起的機體鼓振。固定起落架機型為零,它們的機體外形從不改變。
調高: 放起落架時更多鼓振。
調低: 放起落架飛行更乾淨。
設定理由: Sets gear aerodynamic buffet; movement and ground-contact cues are separate.
Effect gains · Engine, mechanical & drag
Touchdown thump65%
機輪觸及跑道那一下的單次衝擊,按下沉率縮放:輕柔著陸是耳語,結實到達是一記悶響。
調高: 觸地時更硬的一擊。
調低: 更柔的到達。
設定理由: Sets landing-impact strength; landing telemetry and response shape determine the pulse.
Reverse rumble0%
反推或槳葉beta區工作時的滑跑振動。無反推機型為零。
調高: 反推下更粗糙的滑跑。
調低: 更含蓄的反推。
設定理由: Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue.
Engine rumble16%
從慢車到全功率跟隨轉速的持續動力裝置振動——前方有東西在燒油的永恆提醒。
調高: 桿裡更多引擎。
調低: 更含蓄的引擎。
設定理由: Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration.
Flap motion12%
僅在模擬器報告襟翼舵面確實移動時的持續振動。它跟隨真實作動器的運動和故障,而非估算的計時器。
調高: 襟翼移動中更多振動。
調低: 更含蓄的襟翼行程。
設定理由: Sets texture from observed flap movement; a command without movement does not establish the cue.
Autopilot follow
AP follow authority10%
自動駕駛指令可以讓桿實際移動多遠。在MSFS中保持極小,因為移動的軸可能被讀回為飛行員輸入;零則完全停用跟隨。
調高: 自動駕駛讓你的桿移動得明顯更多。
調低: 幾乎察覺不到的跟隨。
設定理由: Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply.
Autopilot
Autopilot · Follow enabledTrue
Whether this feature is active in this profile.
設定理由: Following is on at 0.1 authority when a supported, valid autopilot control reference is available.
Autopilot · Neutral hold enabledFalse
Whether this feature is active in this profile.
設定理由: Permits centering hold during a supported AP state, separate from following a moving target.
Autopilot · Neutral hold strength0.6
設定理由: Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled.
Stick feel
StickFeel · Trim feel enabledTrue
Whether this feature is active in this profile.
設定理由: Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
StickFeel · Trim relief enabledTrue
Whether this feature is active in this profile.
設定理由: Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
StickFeel · Force trim enabledFalse
Whether this feature is active in this profile.
設定理由: Enables local force trim, separate from aircraft-owned trim and add-on integration qualification.
StickFeel · G load enabledTrue
Whether this feature is active in this profile.
設定理由: Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it.
StickFeel · Rate damping enabledTrue
Whether this feature is active in this profile.
設定理由: Enables rate damping with the configured coefficients and control law.
Aero
Aero · Max flap index2
Where this effect reaches full strength (or has fully faded, for washouts).
調高: a more gradual build to a later peak.
調低: a quicker build.
設定理由: Sets the final flap index for detent normalization. UP plus three detents uses maximum index3.
Aero · Min flap index1
Where this effect begins fading in.
調高: the effect begins later.
調低: it begins earlier.
設定理由: Sets the first flap detent that admits buffet; this is a handle index, not degrees.
Aero · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions.
Aero · Shaker enabledFalse
Whether this feature is active in this profile.
設定理由: Permits shaker at supported warning conditions; the switch does not establish aircraft equipment.
Ground
Ground · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables ground effects; each still needs its own strength and contact or motion telemetry.
Engine
Engine · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables engine cues with nonzero settings and valid running-engine telemetry.
Mechanical
Mechanical · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables accessory cues with configured strengths and observed accessory movement.
Mechanical · Gain0
The strength of this effect.
調高: a stronger effect.
調低: a weaker one.
設定理由: Sets texture from observed gear movement, separate from aerodynamic and touchdown effects.
全部設定檔設定
| 引數 | 數值 | 控制作用及原因 |
|---|---|---|
| Spring strength | 0.8 | Mechanical linkage motivates airspeed-sensitive stick resistance. The baseline spring is 0.8. Its low-speed blend reaches baseline strength at 67 KIAS. |
| Spring deadband | 0.04 | Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner. |
| Force gain | 0.7 | The aerodynamic-load gain is 0.7 with an indicated-speed reference of 125 KIAS. This supplies speed-dependent loading alongside the spring. |
| Master gain | 0.85 | Scales overall profile strength while preserving effect balance, subject to device and output limits. |
| Spring full-strength speed | 67 kt | Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| Airspeed spring stiffening | 0.15 | The high-speed spring-stiffening gain is 0.15. It strengthens the permitted spring response above 67 KIAS, with the squared-speed ratio capped at 5. |
| Airspeed stiffening cap | 5 | Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap. |
| Aileron force scale | 0.85 | Roll and pitch aerodynamic scales are 0.85 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled. |
| Elevator force scale | 1 | Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Maximum output force | 0.55 | Caps directed-force output. Native spring effects and device limits remain separate. |
| Autopilot · Follow enabled | True | Following is on at 0.1 authority when a supported, valid autopilot control reference is available. |
| Autopilot · Follow authority | 0.1 | Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply. |
| Autopilot · Neutral hold enabled | False | Permits centering hold during a supported AP state, separate from following a moving target. |
| Autopilot · Neutral hold strength | 0.6 | Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled. |
| StickFeel · Trim feel enabled | True | Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| StickFeel · Trim relief enabled | True | Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| Aero · Max flap index | 2 | Sets the final flap index for detent normalization. UP plus three detents uses maximum index3. |
| Aero · Min flap index | 1 | Sets the first flap detent that admits buffet; this is a handle index, not degrees. |
| Aero · Amplitude | 0.5 | Sets triggered shaker strength; inactive while the shaker feature is disabled. |
| Dynamic-pressure blend | True | Allows baseline spring strength to rise with indicated airspeed where the control law permits it. |
| Minimum spring factor | 0.5 | Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength. |
| Spring wake-up speed | 15 kt | Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit. |
| 力回饋調校速度 | 125 kt | Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
| StickFeel · Elevator authority | 0.3 | The DA40 elevator tab supplies pitch pressure relief, unlike the DA20’s spring-preload system. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0. |
| StickFeel · Aileron authority | 0 | Scales supported roll-trim relief and permitted centre movement. Zero removes roll response. |
| StickFeel · Force trim enabled | False | Enables local force trim, separate from aircraft-owned trim and add-on integration qualification. |
| StickFeel · G load enabled | True | Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it. |
| StickFeel · Rate damping enabled | True | Enables rate damping with the configured coefficients and control law. |
| Aero · Enabled | True | Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions. |
| Aero · Gain | 0.5 | Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings. |
| Aero · Gain | 0 | Sets high-Mach buffet strength; onset and full-strength thresholds are separate. |
| Aero · Gain | 0.28 | Sets flap buffet at the configured position and speed gates. Flap movement texture is separate. |
| Aero · Gain | 0 | Sets gear aerodynamic buffet; movement and ground-contact cues are separate. |
| Aero · Shaker enabled | False | Permits shaker at supported warning conditions; the switch does not establish aircraft equipment. |
| Ground · Enabled | True | Enables ground effects; each still needs its own strength and contact or motion telemetry. |
| Ground · Gain | 0.38 | Sets rolling texture strength, modified by speed, surface and undercarriage configuration. |
| Ground · Gain | 0.25 | Sets gear-bump texture during ground motion, separate from touchdown impact. |
| Ground · Gain | 0.65 | Sets landing-impact strength; landing telemetry and response shape determine the pulse. |
| Ground · Gain | 0 | Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue. |
| Engine · Enabled | True | Enables engine cues with nonzero settings and valid running-engine telemetry. |
| Engine · Gain | 0.16 | Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration. |
| Mechanical · Enabled | True | Enables accessory cues with configured strengths and observed accessory movement. |
| Mechanical · Gain | 0.12 | Sets texture from observed flap movement; a command without movement does not establish the cue. |
| Mechanical · Gain | 0 | Sets texture from observed gear movement, separate from aerodynamic and touchdown effects. |
公開來源 23
- Diamond DA40 Diamond StarResearch background · Wikipedia revision 1373674831 · retrieved 2026-09-12
- Exact product and documentation researchExact COWS product: configurations, AFCS/trim, systems and platformsProduct listing captured 2026-09-30; edition scope from the reviewed catalogue
- DA40 Expansion PackExact product and reviewed configuration passagesProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Diamond-authored DA40NG AFM archived copyDA40NG AFM PDF pp263-267, section7-3 to7-7; PDF263-265/printed7-3 to7-5, revision3; image reviewed
- Diamond official DA40NG G1000 legacy checklist 21.0ZIP DA40_NG_Checklist_Legacy_rev21.pdf p10,
- Publisher DA40NG v1.2.0 current compatibility and trim changesPublisher opening post; Bug Fixes and Improvements
- RealSimGear separate NXi option and aircraft compatibilityProduct compatibility list
- Diamond DA40NG-SimSolutions-DA40XP12version1.3.0 January25,2025 and1.2.x changesProduct listing captured 2026-09-23; edition scope from the reviewed catalogue
- Diamond DA40-180 Diamond StarExact product and reviewed configuration passagesProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Diamond DA40 technical specificationsDiamond DA40
- DA40-180 Diamond StarDiamond DA40
- Flight test: Diamond DA40 NGPhilip Whiteman · 12 June 2015
- DA 40 XLS: The Innovator Keeps Getting BetterMarc C. Lee · 24 February 2009
- Buying a Used Aircraft: Diamond DA40 StarDiamond DA40
- Microsoft Flight Simulator aircraft manuals
- MSFS 2024 FAQ and edition aircraft inventory
- MSFS 2020 FAQ and edition aircraft inventory
- Diamond DA40: Airline Pilot Trainer, Part IIThomas Turner · 27 November 2004
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- Take Command!: RealSimGear DA40NG, X-AviationProduct listing captured 2026-09-23; edition scope from the reviewed catalogue
- Diamond DA40 NG AFM紙質或存檔參考資料；無公開連結
- EASA TCDS A.022紙質或存檔參考資料；無公開連結
- Diamond published data紙質或存檔參考資料；無公開連結
社群與糾錯
如果你的真機經驗表明本頁有誤,請在此指正。
飛行員糾錯
飛過這款飛機?糾正本頁。
本頁基於引用資料構建,而真機經驗勝過任何引用。 請引用有誤的主張,並告訴我們真機的實際表現。糾錯 將交由維護者稽核,並納入本研究的下一次修訂。
登入後即可提交糾錯。無需密碼,只需一次性郵件連結。
登入
機庫閒談
關於 Diamond DA40 的飛行與調校的公開討論(社群論壇)。上方的糾錯將私下送達維護者;機庫閒談是公開的。
Hangar talk for the Diamond DA40 NG. How does the real one feel, and how close does the built-in profile get? Compare cockpit time, tuning tweaks, and community profiles here. Research page: Diamond DA40 NG in the aircra…
社群
該機型的社群配置
| 飛機 | 個人資料 | 模擬器 | 硬體 | Added | Reviews | Discussion | 下載 | Open profile |
|---|---|---|---|---|---|---|---|---|
| DA40-NG AsoboDA40 | DA40-NG Asobo by TheMomiX | MSFS | PicoWinder SideWinder Force Feedback Pro | 1 reply7月 27 | 626 |