Development milestones
First flight: April 9, 1967 ( 1967-04-09 )
機型庫Boeing 737 family
Alf van Beem · Public domain · Boeing 737-800 picturedBoeing 737 family
Artificial pitch q-feel, spring-and-cam roll resistance, autopilot column following and a stick shaker.
AirlinerB738設定檔選項：32 個
瞭解飛機
The first 737 flew in 1967. Boeing retained the six-abreast fuselage width familiar from its earlier jets while placing two engines under the wing. The aircraft subsequently developed through the Original, Classic, Next Generation and MAX generations.
Engines, displays and systems differ between the early 737-200, the 737-800 and the 737 MAX. Simulator products add another layer of variation, from bundled aircraft to specialist implementations with their own failures, options and documentation.
Boeing 737-800
- Powerplant
- 2× CFM56-7B, up to 27,300 lbf each↗
- Seats
- 162–189↗
- Max takeoff weight
- 174,200 lb (79,016 kg)↗
- Wingspan
- 117 ft 5 in (35.79 m) with winglets↗
- Length
- 129 ft 6 in (39.47 m)↗
- Max operating (Vmo/Mmo)
- 340 KIAS / M0.82↗
- Typical cruise
- M0.785↗
- Max operating altitude
- 41,000 ft↗
- Range
- ≈2,935 nm↗
- Fuel capacity
- 6,875 US gal↗
- Flight controls
- Hydraulic with artificial feel, control column↗
- First flight (NG)
- 1997↗
A cross-country flight in the MAX 9
Bedell’s MAX 9 trip begins with a familiar cockpit wrapped around noticeably larger displays. He describes the same confined working space, overhead switches and trim wheels he knew from earlier 737s, alongside quieter engines and small practical improvements such as extra cupholders and glareshield buttons. The longer engine-start sequence and stronger idle thrust were immediately apparent during preparation and taxi.
Once airborne, he found the initial climb unhurried, although intermediate level-offs prevented a clean comparison. Cruise was where the newer aircraft impressed him: he recorded lower fuel consumption, a quieter cockpit and an arrival ahead of schedule with more fuel than planned. He also preferred its behaviour during full-flap approaches. These are observations from one flight and his operating experience, rather than a controlled performance trial or a general assessment of every MAX variant.
Trading the fighter mission for an airline flight
Wooten describes a striking change in what occupied his attention after leaving the US Air Force in early 2022. In the F-15E, he had concentrated on tactics and employing the aircraft. In the 737, the conversation centred on departure, arrival, weather and giving passengers a smooth journey. He remembers the surprise of making his first actual 737 landing with a cabin full of passengers after the airline’s simulator-based preparation.
That experience did not mean there was nothing left to learn. He was still developing familiarity with the avionics and a new set of cockpit habits, helped by the airline’s mentoring process. The working relationships felt different too: a captain and first officer might share a trip and never meet again, unlike a close-knit fighter squadron.
Learning a lighter touch after the MD-80
The author recalls arriving for the first 737 trip after weeks of ground school, simulator sessions and checks, aware that the passengers could not know it was their pilot’s first flight in the actual aircraft. A check airman accompanied the three-day period of initial operating experience. After many years on the MD-80, the move had been a deliberate search for a new challenge, and confidence grew noticeably between the first and final approaches.
The greatest handling adjustment was learning to use smaller, lighter inputs. The author also welcomed the electronic displays and automated loading of route, weather and loading information, while admitting that the data-entry sequence still required care. Landings took longer to become satisfying, especially as the instructor varied flap settings and the sight picture changed. The account describes the process of becoming comfortable in a new type; its comparisons are the writer’s personal impressions.
公開來源 36
- Boeing 737Research background · Wikipedia revision 1374061079 · retrieved 2026-09-12
- Microsoft Flight Simulator aircraft manuals
- MSFS 2024 FAQ and edition aircraft inventory
- Boeing 737-8000 POH
- X-Plane 12 Desktop Manual
- X-Plane aircraft and avionics manuals
- X-Plane 11 Desktop Manual
- PMDG 737 for MSFS - Introduction (PDF)
- PMDG documentation
- Maintainer installation guide and official Zibo download locations
- 737 MAXOfficial developer / designated store catalogue · checked 2026-09-12
- 737-700 for Microsoft Flight Simulator 2024Official developer / designated store catalogue · checked 2026-09-12
- 737-600 for Microsoft Flight Simulator 2024Official developer / designated store catalogue · checked 2026-09-12
- 737-900 for Microsoft Flight Simulator 2024Official developer / designated store catalogue · checked 2026-09-12
- 737-800 for Microsoft Flight Simulator 2024Official developer / designated store catalogue · checked 2026-09-12
- 737-900 for Microsoft Flight Simulator 2020Official developer / designated store catalogue · checked 2026-09-12
- 737-800 for Microsoft Flight Simulator 2020Official developer / designated store catalogue · checked 2026-09-12
- 737-600 for Microsoft Flight Simulator 2020Official developer / designated store catalogue · checked 2026-09-12
- 737-700 for Microsoft Flight Simulator 2020Official developer / designated store catalogue · checked 2026-09-12
- 732 TwinjetOfficial developer / designated store catalogue · checked 2026-09-12
- iFly 737 MAX8 for MSFSOfficial product and support listing · checked 2026-09-14
- Max delivers on its promisePeter A. Bedell · 2 November 2022
- From Air Force F-15s to airline 737sJamie Hunter interview with Bill Wooten · 10 November 2022
- Boeing 737 Initial Operating Experience: My First TripAAFO4Ever · syndicated first-person account; publication date not established
- 732 TwinJet V4 Pro XP12-FlyJSim-B732-v4Official developer / designated-store reference · checked 2026-09-14
- 732 TwinJet V3 Pro XP11-FlyJSim-B732-v3Official developer / designated-store reference · checked 2026-09-14
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- 737-300 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- 737-400 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- 737-500 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Take Command!: IXEG 737 Classic Plus, X-AviationProduct listing captured 2026-09-23; edition scope from the reviewed catalogue
- Threshold Exclusive: Freeware 'LevelUp' 737NG Series Introduced for X-Plane - ThresholdProduct listing captured 2026-09-30; edition scope from the reviewed catalogue
- LevelUP 737NG Series for XP12 Released - ThresholdProduct listing captured 2026-09-30; edition scope from the reviewed catalogue
- Boeing 737-800 FCOM紙質或存檔參考資料；無公開連結
- Boeing published data紙質或存檔參考資料；無公開連結
- FAA TCDS A16WE紙質或存檔參考資料；無公開連結
設定檔如何建模
Boeing 737-800
Free + ProMSFS 2024X-Plane 12X-Plane 11MSFS 2020
The first 737 flew in 1967. Boeing retained the six-abreast fuselage width familiar from its earlier jets while placing two engines under the wing. The aircraft subsequently developed through the Original, Classic, Next Generation and MAX generations.
The factory starting point selects Boeing 737-800 across MSFS 2024, X-Plane 12, X-Plane 11, MSFS 2020.
Spring resistance builds with the selected airspeed response. Directed aerodynamic loading is omitted.
Pitch-trim relief is off. Autopilot following is enabled for supported control references.
此確切修訂版尚未開放公開安裝。
Controls and trim
The 737's aileron feel uses a cam, roller and spring-centering unit with breakout and gradient that stays constant with airspeed. Pitch artificial feel differs, so the total pitch-to-roll effort balance can change with speed. PMDG's NG introduction also distinguishes electric-trim limits by model and flap state, and CWS from CMD. Those NG details are not automatically MAX, Classic or early-737 interface evidence.
Pitch and roll feel
The aircraft’s documented roll spring is speed-independent. This revision uses a shared profile airspeed response where enabled; it does not provide a separate measured pitch-versus-roll feel schedule.
About the values
The gains are normalized profile settings. They describe the chosen effect balance; hand force depends on the device and its output limits. IAS references are tuning values rather than operating limits. Physical acceptance of this revision remains pending.
Master gain & control system
Master gain100%
施加於模型產出的一切、在裝置上限之前的最終整體輸出縮放。
調高: 一切(彈簧、載荷、效果)一同增強。
調低: 一切一同變柔。
設定理由: Scales overall profile strength while preserving effect balance, subject to device and output limits.
Forces
Spring strength20%
把搖桿拉回中央的基礎回中力。其他所有力都疊加在它之上。太低,正常飛行中搖桿會發軟;太高,它會與你的手較勁,並掩蓋疊加其上的細微提示。
調高: 更硬的回中,更抗手。
調低: 更軟的桿,只靠氣動載荷。
設定理由: The fixed roll-feel mechanism and separate pitch artificial feel motivate distinct axis balance; an aerodynamic scale alone cannot describe total pitch/roll effort. The baseline spring is 0.2. Low-speed spring blending is off.
PMDG 737 for MSFS - Introduction (PDF)Spring deadband0%
中央附近彈簧保持安靜的小中立區,讓靜止時的微小移動不會咔嗒作響。更寬更安穩但更松,更窄更精確但可能在中央附近抖動。
調高: 更安靜但更松的中央,曠量更大。
調低: 更緊的中央,靜止時可能抖動。
設定理由: Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner.
Forces · Center starting force0.08
設定理由: Adds smoothly ramped resistance outside the centre deadband. Zero removes this preload.
Overall aerodynamic load0%
作用於兩條持續軸載荷的主縮放,在它們各自的獨立平衡之前施加。設定檔通常不動它,而是調校兩條軸載荷。
調高: 兩軸載荷一同加重。
調低: 兩軸一同減輕。
設定理由: The 0 gain omits sustained directed airspeed loading. Spring resistance remains independent.
Spring engagement full122 kt
彈簧達到全強度的空速。從起點到這裡,隨著氣流在操縱面上增強,回中逐漸變硬。
設定理由: Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
Centre firmness vs speed100%
在偏轉載荷之外,回中本身隨速度變硬的程度。零則中央手感恆定;越大,巡航時回中越硬,起落航線上越松。
調高: 中央隨速度明顯變硬。
調低: 任何速度下中央手感恆定。
設定理由: The high-speed spring-stiffening gain is 1. It strengthens the permitted spring response above 122 KIAS, with the squared-speed ratio capped at 7.8.
Centre stiffening cap7.8
速度驅動的中央變硬上限,防止高速飛行把彈簧無限上緊。
調高: 高速允許更多總硬化。
調低: 硬化更早封頂。
設定理由: Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap.
Aileron load180%
由副翼偏轉和空速產生的持續橫滾載荷,獨立於俯仰調校。與升降舵載荷一起,決定評測中常說的操縱協調比。
調高: 橫滾力更重。
調低: 副翼更輕更靈。
設定理由: Roll and pitch aerodynamic scales are 1.8 and 0.9, respectively. These stored weights do not create directed aerodynamic loading while that term is inactive. No custom spring-travel curve is enabled.
Elevator load90%
由升降舵偏轉和空速產生的持續俯仰載荷,獨立於橫滾調校。這是決定機型俯仰重量的主槓桿。它不影響副翼、彈簧、配平或抖振力。
調高: 速度下持續俯仰力更重。
調低: 升降舵更輕,握持更省力。
設定理由: Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Max output force70%
每個穩態俯仰或橫滾力到達裝置前的上限,防止猛烈機動中砸擊或飽和硬體。
調高: 削波前更高的穩態力峰值。
調低: 更柔的上限;猛烈機動更早被抹平。
設定理由: Caps directed-force output. Native spring effects and device limits remain separate.
Forces · Center starting force transition0.05
設定理由: Sets the travel used to ramp in centre preload. Wider intervals make its onset more gradual.
Airspeed blendingFalse
啟用低速彈簧介入視窗(上面的起始/全強度節數)。關閉時彈簧在所有速度下恆定。
設定理由: Allows baseline spring strength to rise with indicated airspeed where the control law permits it.
Low-speed spring floor55%
在靜止、空速尚未產生氣動力之前,彈簧還剩多少。下限高,停機時搖桿結實;下限低,則是停放輕型飛機那種鋼索鬆弛的感覺。
調高: 停機和滑行時桿更結實。
調低: 停機時桿發軟,只隨速度甦醒。
設定理由: Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength.
Spring engagement start0 kt
彈簧從低速下限開始向全強度攀升的空速:起飛滑跑中操縱面"甦醒"的那一刻。
設定理由: Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit.
力回饋調校速度280
氣動載荷達到設計滿值的指示空速。它把整條載荷曲線錨定在飛機真實的速度範圍:172在110節就載滿,噴氣機要晚得多。
調高: 載荷來得更晚;桿輕到更高速度。
調低: 載荷來得更早,巡航更沉。
設定理由: Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Trim
Trim relief (elevator)30%
升降舵配平緩解持續俯仰力、移動桿的安定位置的強度。在100 %時,配平得當的飛機不需要保持壓力——正是真實飛行中"用配平消掉載荷"的流程。
調高: 配平消掉更多持續力;100 %時滿配平可完全抵消。
調低: 即使配平也仍要持續用力。
設定理由: Documented electric-trim limits vary with model and flap state; a selected trim response is a simplification and does not recreate every NG or MAX trim law. Pitch relief is off, with stored authority 0.3; roll authority is 0.09.
PMDG 737 for MSFS - Introduction (PDF)Trim relief (aileron)9%
橫滾配平的同類緩解。多數通航機型沒有真正的副翼配平,所以保持為零;有橫滾配平的機型獲得相應的值。
調高: 橫滾配平消掉更多持續力。
調低: 橫滾配平作用更小。
設定理由: Scales supported roll-trim relief and permitted centre movement. Zero removes roll response.
Effect gains · Ground
Runway rumble40%
由輪速和地面型別(鋪裝、草地、礫石)產生的滾動振動。
調高: 桿上更強的地面質感。
調低: 更平滑的滑行。
設定理由: Sets rolling texture strength, modified by speed, surface and undercarriage configuration.
Gear bumps32%
來自伸縮縫、車轍和粗糙地面的短促離散顛簸,為持續隆隆聲打上標點。
調高: 接縫與車轍的衝擊更清晰。
調低: 更柔的地面細節。
設定理由: Sets gear-bump texture during ground motion, separate from touchdown impact.
Effect gains · Airframe
Stick shaker90%
由飛機自身失速警告系統觸發的專用抖桿器振動。只有真有抖桿器的機型才有值;其餘全靠氣動抖振和喇叭。
調高: 更硬的抖桿器。
調低: 更含蓄的抖桿器。
設定理由: Sets triggered shaker strength; inactive while the shaker feature is disabled.
Stall buffet30%
接近失速及失速警告響起時的機體抖動:這副機翼宣告不滿的音量。斷失乾脆的機型抖振收斂,讓喇叭承擔警告。
調高: 更強的失速前顫抖。
調低: 更含蓄的機翼;警告交給喇叭。
設定理由: Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings.
Mach buffet44%
接近馬赫極限的跨音速抖振。對接近MMO的噴氣機有意義,對到不了那裡的活塞機和渦槳機為零。
調高: 接近馬赫極限時更強的跨音速抖振。
調低: 高馬赫下更平滑的飛行。
設定理由: Sets high-Mach buffet strength; onset and full-strength thresholds are separate.
Flap buffet36%
襟翼伸入氣流後機體的低頻振動,發生在它們真正做功的速度視窗內。
調高: 襟翼做功時更粗糙的飛行。
調低: 更柔的進近襟翼。
設定理由: Sets flap buffet at the configured position and speed gates. Flap movement texture is separate.
Gear buffet38%
可收放起落架懸在氣流中引起的機體鼓振。固定起落架機型為零,它們的機體外形從不改變。
調高: 放起落架時更多鼓振。
調低: 放起落架飛行更乾淨。
設定理由: Sets gear aerodynamic buffet; movement and ground-contact cues are separate.
Effect gains · Engine, mechanical & drag
Touchdown thump90%
機輪觸及跑道那一下的單次衝擊,按下沉率縮放:輕柔著陸是耳語,結實到達是一記悶響。
調高: 觸地時更硬的一擊。
調低: 更柔的到達。
設定理由: Sets landing-impact strength; landing telemetry and response shape determine the pulse.
Reverse rumble50%
反推或槳葉beta區工作時的滑跑振動。無反推機型為零。
調高: 反推下更粗糙的滑跑。
調低: 更含蓄的反推。
設定理由: Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue.
Engine rumble11%
從慢車到全功率跟隨轉速的持續動力裝置振動——前方有東西在燒油的永恆提醒。
調高: 桿裡更多引擎。
調低: 更含蓄的引擎。
設定理由: Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration.
Flap motion34%
僅在模擬器報告襟翼舵面確實移動時的持續振動。它跟隨真實作動器的運動和故障,而非估算的計時器。
調高: 襟翼移動中更多振動。
調低: 更含蓄的襟翼行程。
設定理由: Sets texture from observed flap movement; a command without movement does not establish the cue.
Autopilot follow
AP follow authority100%
自動駕駛指令可以讓桿實際移動多遠。在MSFS中保持極小,因為移動的軸可能被讀回為飛行員輸入;零則完全停用跟隨。
調高: 自動駕駛讓你的桿移動得明顯更多。
調低: 幾乎察覺不到的跟隨。
設定理由: Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply.
Autopilot
Autopilot · Follow enabledTrue
Whether this feature is active in this profile.
設定理由: Following is on at 1 authority when a supported, valid autopilot control reference is available.
Autopilot · Neutral hold enabledFalse
Whether this feature is active in this profile.
設定理由: Permits centering hold during a supported AP state, separate from following a moving target.
Autopilot · Neutral hold strength0.6
設定理由: Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled.
Stick feel
StickFeel · Trim feel enabledFalse
Whether this feature is active in this profile.
設定理由: Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
StickFeel · Trim relief enabledFalse
Whether this feature is active in this profile.
設定理由: Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
StickFeel · Force trim enabledFalse
Whether this feature is active in this profile.
設定理由: Enables local force trim, separate from aircraft-owned trim and add-on integration qualification.
StickFeel · G load enabledFalse
Whether this feature is active in this profile.
設定理由: Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it.
StickFeel · Rate damping enabledFalse
Whether this feature is active in this profile.
設定理由: Enables rate damping with the configured coefficients and control law.
Aero
Aero · Max flap index8
Where this effect reaches full strength (or has fully faded, for washouts).
調高: a more gradual build to a later peak.
調低: a quicker build.
設定理由: Sets the final flap index for detent normalization. UP plus three detents uses maximum index3.
Aero · Min flap index1
Where this effect begins fading in.
調高: the effect begins later.
調低: it begins earlier.
設定理由: Sets the first flap detent that admits buffet; this is a handle index, not degrees.
Aero · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions.
Aero · Shaker enabledTrue
Whether this feature is active in this profile.
設定理由: Permits shaker at supported warning conditions; the switch does not establish aircraft equipment.
Spring response
SpringResponse · Travel enabledFalse
Whether this feature is active in this profile.
設定理由: Applies the configured pitch and roll spring travel curves.
SpringResponse · Output1
設定理由: Sets response at the second pitch-curve point; it is an endpoint only if its input position is full travel.
SpringResponse · Output1
設定理由: Sets response at the second roll-curve point; its input position and other points determine the travel law.
Ground
Ground · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables ground effects; each still needs its own strength and contact or motion telemetry.
Engine
Engine · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables engine cues with nonzero settings and valid running-engine telemetry.
Mechanical
Mechanical · EnabledTrue
Whether this feature is active in this profile.
設定理由: Enables accessory cues with configured strengths and observed accessory movement.
Mechanical · Gain0.18
The strength of this effect.
調高: a stronger effect.
調低: a weaker one.
設定理由: Sets texture from observed gear movement, separate from aerodynamic and touchdown effects.
全部設定檔設定
| 引數 | 數值 | 控制作用及原因 |
|---|---|---|
| Spring strength | 0.2 | The fixed roll-feel mechanism and separate pitch artificial feel motivate distinct axis balance; an aerodynamic scale alone cannot describe total pitch/roll effort. The baseline spring is 0.2. Low-speed spring blending is off. |
| Spring deadband | 0 | Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner. |
| Forces · Center starting force | 0.08 | Adds smoothly ramped resistance outside the centre deadband. Zero removes this preload. |
| Force gain | 0 | The 0 gain omits sustained directed airspeed loading. Spring resistance remains independent. |
| Master gain | 1 | Scales overall profile strength while preserving effect balance, subject to device and output limits. |
| Spring full-strength speed | 122 kt | Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| Airspeed spring stiffening | 1 | The high-speed spring-stiffening gain is 1. It strengthens the permitted spring response above 122 KIAS, with the squared-speed ratio capped at 7.8. |
| Airspeed stiffening cap | 7.8 | Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap. |
| Aileron force scale | 1.8 | Roll and pitch aerodynamic scales are 1.8 and 0.9, respectively. These stored weights do not create directed aerodynamic loading while that term is inactive. No custom spring-travel curve is enabled. |
| Elevator force scale | 0.9 | Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Maximum output force | 0.7 | Caps directed-force output. Native spring effects and device limits remain separate. |
| Autopilot · Follow enabled | True | Following is on at 1 authority when a supported, valid autopilot control reference is available. |
| Autopilot · Follow authority | 1 | Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply. |
| Autopilot · Neutral hold enabled | False | Permits centering hold during a supported AP state, separate from following a moving target. |
| Autopilot · Neutral hold strength | 0.6 | Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled. |
| StickFeel · Trim feel enabled | False | Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| StickFeel · Trim relief enabled | False | Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| Aero · Max flap index | 8 | Sets the final flap index for detent normalization. UP plus three detents uses maximum index3. |
| Aero · Min flap index | 1 | Sets the first flap detent that admits buffet; this is a handle index, not degrees. |
| Aero · Amplitude | 0.9 | Sets triggered shaker strength; inactive while the shaker feature is disabled. |
| Forces · Center starting force transition | 0.05 | Sets the travel used to ramp in centre preload. Wider intervals make its onset more gradual. |
| Dynamic-pressure blend | False | Allows baseline spring strength to rise with indicated airspeed where the control law permits it. |
| Minimum spring factor | 0.55 | Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength. |
| Spring wake-up speed | 0 kt | Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit. |
| 力回饋調校速度 | 280 kt | Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
| SpringResponse · Travel enabled | False | Applies the configured pitch and roll spring travel curves. |
| SpringResponse · Output | 1 | Sets response at the second pitch-curve point; it is an endpoint only if its input position is full travel. |
| SpringResponse · Output | 1 | Sets response at the second roll-curve point; its input position and other points determine the travel law. |
| StickFeel · Elevator authority | 0.3 | Documented electric-trim limits vary with model and flap state; a selected trim response is a simplification and does not recreate every NG or MAX trim law. Pitch relief is off, with stored authority 0.3; roll authority is 0.09. |
| StickFeel · Aileron authority | 0.09 | Scales supported roll-trim relief and permitted centre movement. Zero removes roll response. |
| StickFeel · Force trim enabled | False | Enables local force trim, separate from aircraft-owned trim and add-on integration qualification. |
| StickFeel · G load enabled | False | Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it. |
| StickFeel · Rate damping enabled | False | Enables rate damping with the configured coefficients and control law. |
| Aero · Enabled | True | Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions. |
| Aero · Gain | 0.3 | Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings. |
| Aero · Gain | 0.44 | Sets high-Mach buffet strength; onset and full-strength thresholds are separate. |
| Aero · Gain | 0.36 | Sets flap buffet at the configured position and speed gates. Flap movement texture is separate. |
| Aero · Gain | 0.38 | Sets gear aerodynamic buffet; movement and ground-contact cues are separate. |
| Aero · Shaker enabled | True | Permits shaker at supported warning conditions; the switch does not establish aircraft equipment. |
| Ground · Enabled | True | Enables ground effects; each still needs its own strength and contact or motion telemetry. |
| Ground · Gain | 0.4 | Sets rolling texture strength, modified by speed, surface and undercarriage configuration. |
| Ground · Gain | 0.32 | Sets gear-bump texture during ground motion, separate from touchdown impact. |
| Ground · Gain | 0.9 | Sets landing-impact strength; landing telemetry and response shape determine the pulse. |
| Ground · Gain | 0.5 | Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue. |
| Engine · Enabled | True | Enables engine cues with nonzero settings and valid running-engine telemetry. |
| Engine · Gain | 0.11 | Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration. |
| Mechanical · Enabled | True | Enables accessory cues with configured strengths and observed accessory movement. |
| Mechanical · Gain | 0.34 | Sets texture from observed flap movement; a command without movement does not establish the cue. |
| Mechanical · Gain | 0.18 | Sets texture from observed gear movement, separate from aerodynamic and touchdown effects. |
公開來源 36
- Boeing 737Research background · Wikipedia revision 1374061079 · retrieved 2026-09-12
- PMDG 737 for MSFS - Introduction (PDF)PMDG737 introduction PDF 30, 39-41
- Microsoft Flight Simulator aircraft manuals
- MSFS 2024 FAQ and edition aircraft inventory
- Boeing 737-8000 POH
- X-Plane 12 Desktop Manual
- X-Plane aircraft and avionics manuals
- X-Plane 11 Desktop Manual
- PMDG documentation
- Maintainer installation guide and official Zibo download locations
- 737 MAXOfficial developer / designated store catalogue · checked 2026-09-12
- 737-700 for Microsoft Flight Simulator 2024Official developer / designated store catalogue · checked 2026-09-12
- 737-600 for Microsoft Flight Simulator 2024Official developer / designated store catalogue · checked 2026-09-12
- 737-900 for Microsoft Flight Simulator 2024Official developer / designated store catalogue · checked 2026-09-12
- 737-800 for Microsoft Flight Simulator 2024Official developer / designated store catalogue · checked 2026-09-12
- 737-900 for Microsoft Flight Simulator 2020Official developer / designated store catalogue · checked 2026-09-12
- 737-800 for Microsoft Flight Simulator 2020Official developer / designated store catalogue · checked 2026-09-12
- 737-600 for Microsoft Flight Simulator 2020Official developer / designated store catalogue · checked 2026-09-12
- 737-700 for Microsoft Flight Simulator 2020Official developer / designated store catalogue · checked 2026-09-12
- 732 TwinjetOfficial developer / designated store catalogue · checked 2026-09-12
- iFly 737 MAX8 for MSFSOfficial product and support listing · checked 2026-09-14
- Max delivers on its promisePeter A. Bedell · 2 November 2022
- From Air Force F-15s to airline 737sJamie Hunter interview with Bill Wooten · 10 November 2022
- Boeing 737 Initial Operating Experience: My First TripAAFO4Ever · syndicated first-person account; publication date not established
- 732 TwinJet V4 Pro XP12-FlyJSim-B732-v4Official developer / designated-store reference · checked 2026-09-14
- 732 TwinJet V3 Pro XP11-FlyJSim-B732-v3Official developer / designated-store reference · checked 2026-09-14
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- 737-300 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- 737-400 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- 737-500 exact product reviewProduct listing captured 2026-09-24; edition scope from the reviewed catalogue
- Take Command!: IXEG 737 Classic Plus, X-AviationProduct listing captured 2026-09-23; edition scope from the reviewed catalogue
- Threshold Exclusive: Freeware 'LevelUp' 737NG Series Introduced for X-Plane - ThresholdProduct listing captured 2026-09-30; edition scope from the reviewed catalogue
- LevelUP 737NG Series for XP12 Released - ThresholdProduct listing captured 2026-09-30; edition scope from the reviewed catalogue
- Boeing 737-800 FCOM紙質或存檔參考資料；無公開連結
- Boeing published data紙質或存檔參考資料；無公開連結
- FAA TCDS A16WE紙質或存檔參考資料；無公開連結
社群與糾錯
如果你的真機經驗表明本頁有誤,請在此指正。
飛行員糾錯
飛過這款飛機?糾正本頁。
本頁基於引用資料構建,而真機經驗勝過任何引用。 請引用有誤的主張,並告訴我們真機的實際表現。糾錯 將交由維護者稽核,並納入本研究的下一次修訂。
登入後即可提交糾錯。無需密碼,只需一次性郵件連結。
登入
機庫閒談
關於 Boeing 737 family 的飛行與調校的公開討論(社群論壇)。上方的糾錯將私下送達維護者;機庫閒談是公開的。
Thanks, and your PMDG issue is fixed (I think), I'm emailing you a new build to test shortly.
Will check out that video and also use the report an issue button. Didn't want to do that before I asked about it in here, thinking it might be an already known issue or something I did wrong on my side.
Thanks for the great feedback. You might be interested in this : https://www.youtube.com/watch?v=JOSg0tKhfr4 to help you really nail down the tuning :) And that PMDG thing seems like a bug. It should go away. hit the rep…
社群
該機型的社群配置
該機型還沒有社群配置。
調出了自己的風格? 分享一個配置 它就會出現在這裡。