Development milestones
Designer: Ted R. Smith
First flight: 1967
Bibliothèque d'appareilsAerostar 600
No machine-readable author provided. CommonsHelper2 Bot assumed (based on copyright claims). · Public domain · Piper Aerostar — real-aircraft reference photograph.Aerostar 600
Ted Smith's piston twin, later produced by Piper as the Aerostar.
General aviation6 choix de profil
Connaître l'avion
The Aerostar began as a Ted Smith design for executive travel and light transport. Piper acquired the design in 1978 and continued production as the PA-60. That change of ownership explains the different manufacturer names found in references. The simulator entry represents the Aerostar 600; the specification tables identify the family models they describe.
Piper Aerostar · Specifications (700P) · real aircraft; source units retained
- Length
- 34 ft 9.75 in (10.61 m)↗
- Wingspan
- 36 ft 8 in (11.18 m)↗
- Height
- 12 ft 1 in (3.68 m)↗
- Wing area
- 178.2 sq ft (16.56 m² )↗
- Empty weight
- 4,275 lb (1,939 kg)↗
- Gross weight
- 6,315 lb (2,864 kg)↗
- Powerplant
- 2 × Avco Lycoming TIO-540-U2A flat six counter-rotating piston , 350 hp (261 kW) each↗
- Maximum speed
- 306 mph (492 km/h, 266 kn)↗
- Cruise speed
- 242 mph (390 km/h, 210 kn)↗
- Range
- 1,024 mi (1,648 km, 890 nmi)↗
- Service ceiling
- 25,000 ft (7,620 m)↗
- Rate of climb
- 1,840 ft/min (9.4 m/s)↗
En savoir plus sur cet aéronef sur AirframeDB
Push-pull controls and electric trim
The A2A manual describes primary controls operated through push-pull tubes and bellcranks. Electric motors move the elevator and rudder trim tabs, with their positions shown in the cockpit. Its Fowler flaps use hydraulic actuators. This description is scoped to the 600 represented in the manual.
An owner’s experience behind the simulated 600
Gentile chose a normally aspirated Aerostar when buying his own aircraft, preferring its combination of solidity and responsiveness to the balance he perceived in the turbocharged version. He operated it for several years, and that direct experience later helped motivate A2A's choice to develop a simulated 600. His introduction is both an owner's recollection and a developer's explanation of a product in which he has a commercial interest.
One experience was especially memorable. A landing-gear failure during a test flight forced him and his son Jake to make a controlled gear-up landing. Gentile describes the aircraft settling onto its belly and both occupants getting out without incident. He presents the event as something that encouraged further curiosity and learning, alongside his continuing appreciation of the design.
A first launch in someone else’s family aircraft
Durden flew Stan Musick's modified 1977 Aerostar 601P with its owner in the right seat. The departure required him to think ahead as acceleration quickly carried the aircraft into a climb through low cloud. As speed increased, the initially unfamiliar control feel developed into a responsive, stable aeroplane. Once trimmed, it held its condition while he attended to radio calls and the climb toward 23,000 feet.
He later enjoyed steep turns, appreciated the extra overhead windows and found the cabin more spacious than its external appearance suggested. Musick had removed one middle-row seat to suit family travel. Durden also evaluated how a new Garmin display worked with the older autopilot, then returned to hand-flying for the enjoyment of it. The landing completed an enthusiastic report that still recognised the need to understand the aircraft's systems and maintain proficiency. This was a pressurised, turbocharged 601P with modifications, distinct from the normally aspirated 600 represented by A2A.
Decades of ferry flying leave a lasting attachment
Cox traces his affection for the Aerostar to a 1975 flight with Jim Miller in Texas. The view past the nearby spinner, the long nose and the rapidly passing landscape became a distinctive part of the experience for him. Over the following decades, ferrying roughly a dozen 700-series aircraft around the world gave him repeated opportunities to appreciate their speed and control response. He still hoped eventually to own one himself.
His recollections include working with Jim Christy on a television flying segment and delivering the specially prepared Spirit of Kai Tak to Britain before its London-to-Sydney race. Those experiences concerned higher-powered, modified Aerostars rather than the original 600. Cox's enthusiasm also acknowledges the fuel consumed when using their full cruising capability. He enjoyed the way the aircraft looked, responded and carried him over long distances, even while his own aeroplane remained a Mooney.
Sources publiques 7
- Piper AerostarResearch background · retrieved 2026-09-12
- Accu-Sim Aerostar 600Official developer / designated store catalogue · checked 2026-09-12
- Accu-Sim Aerostar 600 ManualScott Gentile · 2025, page 4
- Family rocketRick Durden · September 2011
- Aerostar 702: Still The FastestBill Cox · 1 November 2007
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- FAA JO 7360.1K — aircraft type designatorsActive FAA order; checked 2026-09-14
Comment le profil le modélise
Avia71 Aerostar 601P
Free + ProX-Plane 12Avia71
Avia71 Aerostar 601P is the selected Avia71 configuration.
Spring resistance builds with the selected airspeed response. A separate aerodynamic term adds speed-dependent control load.
Valid trim provides the configured pressure relief. Autopilot following is off.
Cette révision précise n’est pas encore autorisée à l’installation publique.
Aircraft and configuration
The Aerostar began as a Ted Smith design for executive travel and light transport. Piper acquired the design in 1978 and continued production as the PA-60. That change of ownership explains the different manufacturer names found in references. The simulator entry represents the Aerostar 600; the specification tables identify the family models they describe.
Push-pull controls and electric trim
The A2A manual describes primary controls operated through push-pull tubes and bellcranks. Electric motors move the elevator and rudder trim tabs, with their positions shown in the cockpit. Its Fowler flaps use hydraulic actuators. This description is scoped to the 600 represented in the manual.
About the values
Strengths are normalized hardware-feel settings. They set the effect balance; hand force depends on the device and its limits. The IAS reference is a tuning value.
Master gain & control system
Master gain85%
L'échelle globale finale appliquée à tout ce que produit le modèle, avant la limite du périphérique.
Plus : tout (ressort, charges, effets) se renforce ensemble.
Moins : tout s'adoucit ensemble.
Pourquoi ici : Scales overall profile strength while preserving effect balance, subject to device and output limits.
Forces
Spring strength74%
La force de rappel de base qui ramène le manche au neutre. Toutes les autres forces s'empilent dessus. Trop faible, le manche paraît mou en vol normal ; trop forte, elle lutte contre la main et masque les signaux plus fins.
Plus : un centrage plus ferme qui résiste davantage à la main.
Moins : un manche plus mou qui ne compte que sur la charge aérodynamique.
Pourquoi ici : The A2A manual describes primary controls operated through push-pull tubes and bellcranks. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 85 KIAS.
Accu-Sim Aerostar 600 ManualSpring deadband4%
Une petite zone neutre autour du centre où le ressort reste muet, pour que les micro-mouvements à l'arrêt ne vibrent pas. Plus large, c'est plus calme mais plus lâche ; plus étroite, plus précis mais parfois nerveux au neutre.
Plus : un centre plus calme mais plus lâche, avec plus de jeu.
Moins : un centre plus serré qui peut vibrer au repos.
Pourquoi ici : Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner.
Overall aerodynamic load80%
Une échelle maîtresse sur les deux charges d'axe, appliquée avant leur équilibre individuel. Les profils la laissent en général en place et règlent les deux axes.
Plus : les deux axes chargent plus fort.
Moins : les deux axes s'allègent ensemble.
Pourquoi ici : The aerodynamic-load gain is 0.8 with an indicated-speed reference of 190 KIAS. This supplies speed-dependent loading alongside the spring.
Airspeed blendingTrue
Active la fenêtre d'engagement basse vitesse du ressort (début/plein en nœuds ci-dessus). Désactivé, le ressort est constant à toute vitesse.
Pourquoi ici : Allows baseline spring strength to rise with indicated airspeed where the control law permits it.
Low-speed spring floor55%
La part du ressort qui survit à l'arrêt, avant que la vitesse ne crée la moindre force aérodynamique. Un plancher haut garde le manche ferme au parking ; un plancher bas donne le jeu de câbles d'un avion léger au parking.
Plus : un manche plus ferme au parking et au roulage.
Moins : un manche mou au parking qui ne s'éveille qu'avec la vitesse.
Pourquoi ici : Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength.
Spring engagement start30 kt
La vitesse à laquelle le ressort quitte son plancher basse vitesse vers la pleine raideur : le début du réveil des commandes au roulage de décollage.
Pourquoi ici : Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit.
Spring engagement full85 kt
La vitesse où le ressort atteint sa pleine raideur. Entre le début et ce point, le centrage se raffermit avec le vent relatif.
Pourquoi ici : Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it.
Vitesse de réglage des forces190
La vitesse indiquée où la charge aérodynamique atteint son niveau de conception. Elle ancre toute la courbe au domaine réel : un 172 charge dès 110 nœuds, un jet bien plus tard.
Plus : les charges arrivent plus tard ; le manche reste léger jusqu'à plus vite.
Moins : les charges arrivent plus tôt et la croisière pèse davantage.
Pourquoi ici : Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit.
Centre firmness vs speed15%
Combien le centrage lui-même se raidit avec la vitesse, en plus des charges de braquage. Zéro garde un centre constant ; plus fait centrer dur en croisière et souple en tour de piste.
Plus : un centre qui durcit nettement avec la vitesse.
Moins : une sensation de centre constante à toute vitesse.
Pourquoi ici : The high-speed spring-stiffening gain is 0.15. It strengthens the permitted spring response above 85 KIAS, with the squared-speed ratio capped at 5.
Centre stiffening cap5
La limite haute du raidissement lié à la vitesse, pour que le vol très rapide ne remonte pas le ressort sans borne.
Plus : plus de raidissement total permis à haute vitesse.
Moins : le raidissement se bride plus tôt.
Pourquoi ici : Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap.
Aileron load82%
La charge de roulis soutenue issue du braquage d'ailerons et de la vitesse, équilibrée indépendamment du tangage. Avec la charge de profondeur, elle fixe l'harmonie des commandes dont parlent les essais.
Plus : des efforts de roulis plus lourds.
Moins : des ailerons plus légers, plus vifs.
Pourquoi ici : Roll and pitch aerodynamic scales are 0.82 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled.
Elevator load100%
La charge de tangage soutenue issue du braquage de profondeur et de la vitesse, équilibrée indépendamment du roulis. Le levier principal du poids en tangage d'un type. Il ne touche ni ailerons, ni ressort, ni trim, ni buffet.
Plus : des efforts de tangage soutenus plus lourds en vitesse.
Moins : une profondeur plus légère, moins musclée à tenir.
Pourquoi ici : Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings.
Max output force55%
Un plafond par force stable de tangage ou roulis avant le périphérique : la garde contre le claquement ou la saturation du matériel en manœuvre forte.
Plus : des pics de force stable plus élevés avant écrêtage.
Moins : un plafond plus doux ; les manœuvres dures s'aplatissent plus tôt.
Pourquoi ici : Caps directed-force output. Native spring effects and device limits remain separate.
Trim
Trim relief (elevator)30%
Combien le trim de profondeur soulage l'effort tenu et déplace le point de repos du manche. À 100 %, un avion bien compensé ne demande aucune pression : le geste réel de compenser la charge.
Plus : le trim retire plus d'effort tenu ; à 100 %, plein trim l'annule.
Moins : vous continuez à tenir de l'effort même compensé.
Pourquoi ici : The A2A manual describes primary controls operated through push-pull tubes and bellcranks. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0.
Accu-Sim Aerostar 600 ManualTrim relief (aileron)0%
Le même soulagement pour le trim de roulis. La plupart des avions légers n'ont pas de vrai trim d'ailerons, donc zéro ; les types qui en ont reçoivent une valeur adaptée.
Plus : le trim de roulis retire plus d'effort tenu.
Moins : le trim de roulis fait moins.
Pourquoi ici : Scales supported roll-trim relief and permitted centre movement. Zero removes roll response.
Effect gains · Ground
Runway rumble40%
Vibration de roulement issue de la vitesse des roues et du revêtement : la texture du bitume, de l'herbe ou du gravier sous le train.
Plus : une texture de surface plus forte dans le manche.
Moins : un roulage plus lisse.
Pourquoi ici : Sets rolling texture strength, modified by speed, surface and undercarriage configuration.
Gear bumps25%
Chocs courts et distincts des joints, ornières et surfaces rugueuses : la ponctuation au-dessus du grondement continu.
Plus : des chocs plus nets des joints et ornières.
Moins : des détails de sol plus doux.
Pourquoi ici : Sets gear-bump texture during ground motion, separate from touchdown impact.
Effect gains · Airframe
Stall buffet35%
Buffet de cellule à l'approche du décrochage et pendant l'avertisseur : la voix de cette aile quand elle est mécontente. Les types à décrochage franc reçoivent un buffet modéré, le klaxon porte l'alerte.
Plus : un tremblement pré-décrochage plus fort.
Moins : une aile plus discrète ; le klaxon porte l'alerte.
Pourquoi ici : Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings.
Mach buffet0%
Buffet transsonique près de la limite de Mach. Parlant pour les jets près de MMO, zéro pour pistons et turbopropulseurs qui n'y vont jamais.
Plus : un buffet transsonique plus fort près de la limite de Mach.
Moins : un vol plus lisse à haut Mach.
Pourquoi ici : Sets high-Mach buffet strength; onset and full-strength thresholds are separate.
Flap buffet0%
Vibration basse fréquence de cellule avec les volets dans le vent, dans la fenêtre où ils travaillent vraiment l'air.
Plus : un vol plus rugueux volets au travail.
Moins : des volets d'approche plus doux.
Pourquoi ici : Sets flap buffet at the configured position and speed gates. Flap movement texture is separate.
Gear buffet0%
Le tambourinement du train rentrant sorti dans le flux. Zéro pour les trains fixes, dont la cellule ne change jamais de forme.
Plus : plus de tambourinement train sorti.
Moins : un vol train sorti plus propre.
Pourquoi ici : Sets gear aerodynamic buffet; movement and ground-contact cues are separate.
Stick shaker50%
Le vibreur de manche dédié, déclenché par l'avertisseur de décrochage de l'avion. Seuls les types à vrai vibreur reçoivent une valeur ; les autres comptent sur buffet et klaxon.
Plus : un vibreur plus dur.
Moins : un vibreur plus discret.
Pourquoi ici : Sets triggered shaker strength; inactive while the shaker feature is disabled.
Effect gains · Engine, mechanical & drag
Touchdown thump65%
Le coup unique au toucher, proportionnel au taux de chute : un kiss se murmure, une arrivée ferme cogne.
Plus : un coup plus dur au toucher.
Moins : des arrivées plus douces.
Pourquoi ici : Sets landing-impact strength; landing telemetry and response shape determine the pulse.
Reverse rumble0%
Vibration de roulage sous inversion de poussée ou plage bêta. Zéro pour les types sans reverse.
Plus : un roulage plus rugueux sous reverse.
Moins : une reverse plus discrète.
Pourquoi ici : Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue.
Engine rumble12%
Vibration continue du moteur suivant le régime du ralenti à la pleine puissance : le rappel permanent que quelque chose brûle du carburant devant.
Plus : plus de moteur dans le manche.
Moins : un moteur plus discret.
Pourquoi ici : Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration.
Flap motion12%
Vibration continue seulement pendant que le simulateur signale les volets réellement en mouvement. Elle suit la course réelle et les pannes, pas un minuteur estimé.
Plus : plus de vibration volets en mouvement.
Moins : des courses de volets plus discrètes.
Pourquoi ici : Sets texture from observed flap movement; a command without movement does not establish the cue.
Autopilot follow
AP follow authority10%
Jusqu'où les ordres du pilote automatique peuvent bouger le manche physique. Minuscule dans MSFS, où un axe déplacé peut être relu comme entrée pilote ; zéro coupe le suivi.
Plus : le pilote automatique bouge visiblement plus votre manche.
Moins : un suivi à peine perceptible.
Pourquoi ici : Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply.
Stick feel
StickFeel · Trim feel enabledFalse
Whether this feature is active in this profile.
Pourquoi ici : Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement.
StickFeel · Trim relief enabledTrue
Whether this feature is active in this profile.
Pourquoi ici : Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount.
StickFeel · Force trim enabledFalse
Whether this feature is active in this profile.
Pourquoi ici : Enables local force trim, separate from aircraft-owned trim and add-on integration qualification.
StickFeel · G load enabledTrue
Whether this feature is active in this profile.
Pourquoi ici : Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it.
StickFeel · Rate damping enabledTrue
Whether this feature is active in this profile.
Pourquoi ici : Enables rate damping with the configured coefficients and control law.
Autopilot
Autopilot · Follow enabledFalse
Whether this feature is active in this profile.
Pourquoi ici : Autopilot following is off; the configured spring and load retain the hardware feel.
Autopilot · Neutral hold enabledFalse
Whether this feature is active in this profile.
Pourquoi ici : Permits centering hold during a supported AP state, separate from following a moving target.
Autopilot · Neutral hold strength0.6
Pourquoi ici : Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled.
Aero
Aero · EnabledTrue
Whether this feature is active in this profile.
Pourquoi ici : Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions.
Aero · Max flap index3
Where this effect reaches full strength (or has fully faded, for washouts).
Plus : a more gradual build to a later peak.
Moins : a quicker build.
Pourquoi ici : Sets the final flap index for detent normalization. UP plus three detents uses maximum index3.
Aero · Min flap index2
Where this effect begins fading in.
Plus : the effect begins later.
Moins : it begins earlier.
Pourquoi ici : Sets the first flap detent that admits buffet; this is a handle index, not degrees.
Aero · Shaker enabledFalse
Whether this feature is active in this profile.
Pourquoi ici : Permits shaker at supported warning conditions; the switch does not establish aircraft equipment.
Ground
Ground · EnabledTrue
Whether this feature is active in this profile.
Pourquoi ici : Enables ground effects; each still needs its own strength and contact or motion telemetry.
Engine
Engine · EnabledTrue
Whether this feature is active in this profile.
Pourquoi ici : Enables engine cues with nonzero settings and valid running-engine telemetry.
Mechanical
Mechanical · EnabledTrue
Whether this feature is active in this profile.
Pourquoi ici : Enables accessory cues with configured strengths and observed accessory movement.
Mechanical · Gain0.12
The strength of this effect.
Plus : a stronger effect.
Moins : a weaker one.
Pourquoi ici : Sets texture from observed gear movement, separate from aerodynamic and touchdown effects.
Tous les réglages du profil
| Paramètre | Valeur | Ce que cela contrôle et pourquoi |
|---|---|---|
| Spring strength | 0.74 | The A2A manual describes primary controls operated through push-pull tubes and bellcranks. The baseline spring is 0.74. Its low-speed blend reaches baseline strength at 85 KIAS. |
| Spring deadband | 0.04 | Sets travel around the centre before the baseline spring resists. Smaller values engage it sooner. |
| Force gain | 0.8 | The aerodynamic-load gain is 0.8 with an indicated-speed reference of 190 KIAS. This supplies speed-dependent loading alongside the spring. |
| Master gain | 0.85 | Scales overall profile strength while preserving effect balance, subject to device and output limits. |
| Dynamic-pressure blend | True | Allows baseline spring strength to rise with indicated airspeed where the control law permits it. |
| Minimum spring factor | 0.55 | Sets low-speed spring strength as a fraction of baseline when blending is enabled. One keeps full strength. |
| Spring wake-up speed | 30 kt | Sets the IAS where the low-speed spring blend starts rising. This is a feel threshold, not a flight limit. |
| Spring full-strength speed | 85 kt | Sets the IAS where the low-speed blend reaches baseline strength; high-speed stiffening also uses it. |
| Vitesse de réglage des forces | 190 kt | Sets the IAS reference for aerodynamic loading. It is an estimate, not published cruise TAS or a flight limit. |
| Airspeed spring stiffening | 0.15 | The high-speed spring-stiffening gain is 0.15. It strengthens the permitted spring response above 85 KIAS, with the squared-speed ratio capped at 5. |
| Airspeed stiffening cap | 5 | Limits the squared airspeed ratio used for high-speed spring stiffening; it is not a device-force cap. |
| Aileron force scale | 0.82 | Roll and pitch aerodynamic scales are 0.82 and 1, respectively. They set the aerodynamic axis balance. No custom spring-travel curve is enabled. |
| Elevator force scale | 1 | Scales pitch aerodynamic loading; pitch spring travel and trim responses are separate settings. |
| Maximum output force | 0.55 | Caps directed-force output. Native spring effects and device limits remain separate. |
| StickFeel · Trim feel enabled | False | Retained for compatibility and group membership. Trim relief, rather than this flag, controls centre movement. |
| StickFeel · Trim relief enabled | True | Allows trim relief with supported control law and valid telemetry. Axis authorities set its amount. |
| StickFeel · Elevator authority | 0.3 | The A2A manual describes primary controls operated through push-pull tubes and bellcranks. Pitch authority 0.3 provides load relief and permitted centre movement; roll authority is 0. |
| StickFeel · Aileron authority | 0 | Scales supported roll-trim relief and permitted centre movement. Zero removes roll response. |
| StickFeel · Force trim enabled | False | Enables local force trim, separate from aircraft-owned trim and add-on integration qualification. |
| StickFeel · G load enabled | True | Allows load-factor changes to modify permitted spring laws. Passive fly-by-wire feel can suppress it. |
| StickFeel · Rate damping enabled | True | Enables rate damping with the configured coefficients and control law. |
| Autopilot · Follow enabled | False | Autopilot following is off; the configured spring and load retain the hardware feel. |
| Autopilot · Follow authority | 0.1 | Sets admitted AP-follow gain, not a percentage of travel. Runtime ownership and input limits still apply. |
| Autopilot · Neutral hold enabled | False | Permits centering hold during a supported AP state, separate from following a moving target. |
| Autopilot · Neutral hold strength | 0.6 | Sets admitted AP neutral-hold strength; inactive while neutral hold is disabled. |
| Aero · Enabled | True | Enables aerodynamic cues; each still needs nonzero strength and its simulator conditions. |
| Aero · Gain | 0.35 | Sets stall-buffet strength. Zero removes the cue without changing simulator stalls or warnings. |
| Aero · Gain | 0 | Sets high-Mach buffet strength; onset and full-strength thresholds are separate. |
| Aero · Gain | 0 | Sets flap buffet at the configured position and speed gates. Flap movement texture is separate. |
| Aero · Max flap index | 3 | Sets the final flap index for detent normalization. UP plus three detents uses maximum index3. |
| Aero · Min flap index | 2 | Sets the first flap detent that admits buffet; this is a handle index, not degrees. |
| Aero · Gain | 0 | Sets gear aerodynamic buffet; movement and ground-contact cues are separate. |
| Aero · Shaker enabled | False | Permits shaker at supported warning conditions; the switch does not establish aircraft equipment. |
| Aero · Amplitude | 0.5 | Sets triggered shaker strength; inactive while the shaker feature is disabled. |
| Ground · Enabled | True | Enables ground effects; each still needs its own strength and contact or motion telemetry. |
| Ground · Gain | 0.4 | Sets rolling texture strength, modified by speed, surface and undercarriage configuration. |
| Ground · Gain | 0.25 | Sets gear-bump texture during ground motion, separate from touchdown impact. |
| Ground · Gain | 0.65 | Sets landing-impact strength; landing telemetry and response shape determine the pulse. |
| Ground · Gain | 0 | Sets reverse-thrust vibration with valid reverser and engine conditions. Zero removes the cue. |
| Engine · Enabled | True | Enables engine cues with nonzero settings and valid running-engine telemetry. |
| Engine · Gain | 0.12 | Sets estimated engine vibration using configured telemetry and response, not measured cockpit vibration. |
| Mechanical · Enabled | True | Enables accessory cues with configured strengths and observed accessory movement. |
| Mechanical · Gain | 0.12 | Sets texture from observed flap movement; a command without movement does not establish the cue. |
| Mechanical · Gain | 0.12 | Sets texture from observed gear movement, separate from aerodynamic and touchdown effects. |
Sources publiques 7
- Piper AerostarResearch background · retrieved 2026-09-12
- Accu-Sim Aerostar 600Official developer / designated store catalogue · checked 2026-09-12
- Accu-Sim Aerostar 600 ManualScott Gentile · 2025, page 4
- Family rocketRick Durden · September 2011
- Aerostar 702: Still The FastestBill Cox · 1 November 2007
- ICAO Doc 8643 — aircraft type designatorsPublic search data retrieved 2026-09-14; authority update 2026-09-03
- FAA JO 7360.1K — aircraft type designatorsActive FAA order; checked 2026-09-14
Communauté et corrections
Si votre expérience du type dit que cette page se trompe, corrigez-la ici.
Corrections de pilotes
Vous volez sur cet appareil ? Corrigez cette page.
Cette page repose sur des références citées, et l'expérience réelle du type vaut mieux qu'une citation. Citez l'affirmation erronée et dites-nous ce que fait l'appareil réel. Les corrections vont au mainteneur pour examen et nourrissent la prochaine révision de cette recherche.
Connectez-vous pour envoyer une correction. Pas de mot de passe, juste un lien e-mail à usage unique.
Se connecter
Discussions de hangar
Conversation ouverte sur le pilotage et le réglage du Aerostar 600, sur le forum communautaire. Les corrections ci-dessus vont en privé au mainteneur ; les discussions de hangar sont publiques.
Connectez-vous pour la lancer. Pas de mot de passe, juste un lien e-mail à usage unique.
Se connecter
Communauté
Profils communautaires pour cet appareil
Pas encore de profils communautaires pour cet appareil.
Réglé à votre façon ? Partagez un profil et il apparaîtra ici.